Recent content by tangodownNZ

Does anybody know if it is possible to calibrate a SEGA Ghost Squad light gun with software before the signals gets sent to MAME. Although I have the gun working (connected to PC via U-HID), I am not convinced the aiming is as good as it could be. A friend told me “You need some other...

Zebra, Your youtube video inspired me to make a lightgun machine and connect it to a U-HID. I have successfully completed it. The hardest part was actually the recoil. I copied you as much as I could with the ne555. I hooked the recoil signal wire to the uhid. But I could not figure out how...

Purbeast. I don’t know what you are talking about. But. I did what zebra done. I use a ghost squad gun, a ghost squad gun sense board, LED screen array, a ghost squad fuse board, a ne555 and a U-HID Nano from ultimarc. Connect that all up and your good, haha I would try a different board and...

Zebra, Your youtube video inspired me to make a lightgun machine and connect it to a U-HID. I have successfully completed it. The hardest part was actually the recoil. I copied you as much as I could with the ne555. I hooked the recoil signal wire to the uhid. But I could not figure out how...

JayBee got back to me. Unlike others on that site who could have helped but didn’t. Thank you JayBee and MickyMac Actually I have moved away from Mame Hooker. Even if it did work. As soon as you use a different emulator you have no recoil. So I am just using the uhid config utility to send 5...

Thank you nem I just plug the recoil signal wire into my U-HID and use the U-HID config utility to send 5 volts to the recoil signal wire.

Yes, its really cool to get it up and running. I will post some photos when I am happy with it. I had a lot of help from twistedsymphony Thank you so much for this information. Do you know where I can find that software by any chance? I have found JB but he’s probably busy

I have the Sega Ghost Squad gun hooked up to the gun sense board. Its working and I can use it with Mame. I am trying to get the recoil output to go through my Ultimarc U-HID to the recoil signal wire. I believe mame hooker can do this, but I can not get mame hooker to see the game. Rom, parent...

Thank you nem. I already have the recoil signal wire hooked up to the trigger wire. It works but messes up the trigger signal because of splitting the circuit I guess. The trigger signal stays on for about two seconds which is a burst. As soon as I disconnect the recoil signal wire from the...

Does anybody know if the Dolphin emulator has a recoil output?

Hello Arcade Enthusiasts, I know this has been done before, but the threads on this topic have become complicated to follow. I have a Ghost Squad gun with gun sense board and a fuse board. The fuse board has a recoil signal wire which requires 5 volts - I currently hook this wire to the...

YES! I got the recoil to work through the fuse board (after frying one mosfet). So I can now fake the recoil using the trigger. The trigger wire carries 5 volts when energised. So this goes to the 1PGUN wire, which tells the MOSFET on the fuse board to release the 24 volts to the solenoid. The...

bagheera369 said: https://segaretro.org/images/5/55/GhostSquadEvolution_Lindbergh_US_DigitalManual.pdf Trace down the gun lines, on page 84/85 At this point, its been years since I've touched one of those, but the FET's on that fuse board, work the same as they do on a Pinball machine, and are...

I have reposted this with the specific title of finding the recoil signal wire, which I believe is 1PGUN on the fuse board. I am also trying to find out how to get this wire to fire the solenoid (without the I/O board, so faking the signal) Thanks to @twistedsymphony I have just finished my...

Thank you very much bagheera369! There are some nice clues there. I traced the lines but seem to come to a dead end. I still can not figure out the fets and where they are on the schematic? I only get as far as RA60P pin 53 (I/O board), and the end of the line at grid line “A” I’m also...