Search results

Can anybody tell me what (important) changes were made between v2.3 and v2.5? I've built a v2.3 advanced PCB a little while ago but never got around to using it. However, I'd like to use it now and am wondering if I need to fix anything, etc.

I'm wiring a custom arcade cabinet and I'm confused about the output from my audio switcher and input to a car amplifier. Here's the diagram: The source devices have line output 3.5mm stereo jacks and the Extron Audio Switcher has 3.5mm stereo input jacks. However, the Extron Audio Switcher...

Thanks so much! Does Mouser not sell them? I can't seem to find JST-VH on their website?

What's the power connector called? I need to make a new cable to plug into the HAS and looking to order from Mouser/Digikey.

Is there a change log for version 2.3 to 2.5? I’ve built a board a few months (?) ago but I’m wondering what’s different.

I'm trying to order the parts for the latest v2.3 revision, but inside the ZIP there are two BOM PDFs? ("MiniGun Supergun ADV - BOM - Sheet1.pdf" and "MiniGun Supergun ADV - BOM.pdf") What's the difference and which one is correct?

Does anybody know if I can use PCB feet/standoffs (?) to raise my Neo Geo MV1C so it's flush with the HAS v4? Right now if I lay them both on my desk, the JAMMA connector doesn't line up. I should have taken a picture before I left for work but hopefully somebody knows what I'm talking about...

Really sorry about your loss undammed. Really sucks. I re-tweeted your complaint to DHL USA so hopefully they can get somebody to actually look for the package. In the mean time, I went ahead and ordered the terminal block versions. Are there any 3d printable cases that anybody has designed...

I haven't modded it yet, but it looks like the stereo left/right channels are accessible on the board. I was wondering if these could be connected somehow to the Minigun? Is there any current way to connect the MV1C to stereo output on the current Minigun?

Is it possible to get stereo sound through the MiniGun with a Neo Geo MVS MV1C?

Thanks! I got it calibrated and it looks absolutely fantastic! Thanks everybody!

Sorry, but where is the Neo-Geo MVS color bar test screen? I'm using a UniBios 4.0 but I can only see a Cross Hatch test?

Thanks again Frank. I'm trying my best to understand but a lot of this I just can't get through my thick head! Hopefully one last(?) question... Does anybody know if the SCART cable included with the NESRGB will work OK with the Minigun and the OSSC? (I don't know if this SCART cable has...

Does anybody have any suggestions on a 6 conductor power cable to go between the MiniGun and the PSU? This braided one in arcadeqc's post looks really clean and perfect: It looks like a molex connector/cable from a computer PSU?

Is the voltage level still safe (under 1.46Vp-p?) if the potentiometers are off? (i.e. turned all the way to the left) Also ... is the goal to get a specific voltage to the THS regardless of the arcade board? For example, is the goal to always send 0.7Vp-p into the THS for correct levels? It...

Can anybody try to explain how the potentiometers work to adjust the input signal? I've always been confused because I thought they are only adjusting (i.e. lowering) the RGB voltage. For example, if the Neo Geo RGB is 4v p-p then it must get reduced to 0.7v p-p for the OSSC, etc. Am I...

In addition to my above questions, can anybody tell me the default mapping of Neo Geo buttons to Dualshock 4 buttons? (i.e. 'A' -> Square, 'B' -> Cross, etc)

Yes, is it the only labeled "THS7374 CIRCUIT" ? It looks like it's just some capacitors and resistors so it looks easy enough to build. Although, it would be a bit messy on a prototype board due to the number of components? If that's the entire circuit I need then I will definitely consider...

Yeah, I'm building one of those too actually (haha) along with buying a HAS from RGB, but they require the JAMMA PCB to be connected to the supergun. I'm looking for a solution that I just connect the RGBS wires directly and get an output. Arcade PCB -> JAMMA harness -> (RGBS high-impedance to...

Thanks a bunch! It looks like it's out of stock but I'll send him an e-mail to see if he is still producing them. I also need to look into how to convert the audio signal... (BTW - I've also pre-ordered a HAS from you a while ago... thanks for everything you do!)