Search Results

Search results 1-20 of 23.

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Hello guys I just want to update you guys with this mod problem Danexmurder point out that the coax cable could be the source of this problem so I look thru my stuff and I found another thicker coax cable so I solder it try and here it is perfect picture, no interference, sound all good now, I just want to thank everyone that comment with suggestions, Kavas, steam313, velyks, Epyc, Danexmurder, thanks to all you guys with sharing and helping out I have other projects that am working on I got a d…

  • Hello guys am back with some improvements, I solder the 3 jumpers I didn’t because of the place I got the instructions this step wasn’t there, then check resolder the pins on the chips and re test, now the colors are good got sound but the pictures comes and goes and there’s some lines in picture here some pictures I also have hooked up rgb in crt monitor and no problem hope any body has any idea thank you very close arcade-projects.com/forums/ind…771fbc4b6d0915a1ceff561b0arcade-projects.com/for…

  • Quote from Velyks: “Quote from alexvw: “Hello guys so am back, with some interesting stuff, after checking some turned out that HDMI cable was causing the problem with no picture, so now that I have picture the colors aren’t right and have no sound, I recheck everything I couldn’t find any problem with installation, am using an USA region board not sure if someone else ran in this problem before. here some pictures, thank you ” Did you solder the three small jumpers? If you don't solder those yo…

  • Hello guys so am back, with some interesting stuff, after checking some turned out that HDMI cable was causing the problem with no picture, so now that I have picture the colors aren’t right and have no sound, I recheck everything I couldn’t find any problem with installation, am using an USA region board not sure if someone else ran in this problem before. here some pictures, thank you

  • Hello kavas thanks for the suggestions I will recheck everything tomorrow and I will post pictures of the installation points I might it missed something then

  • Hello thank you for the response, I did purchase kit from VGP according with your response it’s already preflashed, so after a got done with installed I assembled a & b board and fired it up hooked up to tv via hdmi and no image, so I figured I needed to flash the kit in last step, unless I miss something that I don’t think,I rechecked all the work with instructions but I will go over one last time so maybe this kit was not flashed so ones I receive the usb programmer. I’ll find out if I run in …

  • hope is better now "Thchardcore" No Trump 2020

  • hello guys, I need some help in programming this CPS2 AV Digital. I already installed the kit and follow all the instructions step by step I don't think I miss any step but, am ready for the final step programming the CPS2 AV Digital so I downloaded cps2_digiav-master file an I think it has all necessary files that I need and will required an altera USB programmer or equivalent. I have order in ebay is on its way I also know that I need software and drivers for it but I couldn't find any step by…

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    so I tried the rom pack it looks like is the same pack I was running so this means that need to performed firmware update so I found in ebay STM32F4DISCOVERY its on its way am trying to prep everything I need to performed this firmware update so I downloaded sd_bootloader file still need to download application STM32 ST-Link Utility ok no problem but the 1 I cant find is the actual firmware update file please help me find this file thanks

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    Oooooh ok sure thank you no problem hope this is all I need to have this problem solved

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    I do have the key writing wires but not sure what firmware I have is there a way to check so that way I can loaded with correct rom set and where I can download it links some links that I tried are dead

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    So I’d been doing more digging not sure but appears that I was running an old rom pack so I reloaded sd card with another set of roms and hasn’t reset so at the end of the instructions CPS2 multi boot v3.1 at the end there’s a section saying that I wed to get the latest rom set but how do I know what version o have in my kit so I can match it with right pack of roms and where I can download itarcade-projects.com/forums/ind…771fbc4b6d0915a1ceff561b0arcade-projects.com/forums/ind…771fbc4b6d0915a1c…

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    So I let the system in couple of games and still no different it actually now is acting up in other games that I didn’t have problems with I going to try another set of roms any suggestions to a compatible rom pack that can I use to reload sd card

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    Not sure yet am going to let it run in demo mode with couple of games and see what happens the 1 is giving me trouble is vapire savior us and ssf2t is hope is the roms might be corrupted but as far 5v rail voltages now I can adjusted to a better voltage I just hope there was a way to post a small video can appreciate better the problem

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    After I replace the wires of 5v rail now is the highest it goes I took that pic for you guys to see the problem was cheap Chinese jamma hardness and you are right a tested a few other games and no problem this happens when I run vapire savior am going to keep testing tonight and probably re wire the other supergun

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    Ok so recheck my supergun focus in 5v power rail turned out the jamma hardness wires wore too thin so I re wired it re test and gain more power as shown in this 2 pictures 1 I try to run the multi kit and still resets I adjusted it to 5.15v still same issue then in voltage regulator now I can go up to 5.35v as shown in this 2 pictures

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    Ok good sorry guys am just trying to make sure if there was any other issue if that’s the case I’ll do whatever it takes to get those voltages go up probably am going to try another PSU like the ones recommended am going to work on this PSU issue and then re evaluate

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    In 1 of the supergun that I built has the same PSU as the 1 in picture that mitsurugi posted

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    Ok the strange thing is that a built 2 superguns with 2 different power supply unit and both same result you guy still suggest to change PSU with a better one any suggestions in what brand I should go that is consistent please advise

  • CPS2 Multi Help!!

    alexvw - - Capcom's CPS2

    Post

    Ok so I got back from work and check 5v rail at jamma connector was 4.8v so adjusted to 5v was not able to go any higher that’s the max and still reboots I took a small video try to posted but I guess is to big of a file