Search Results

Search results 1-20 of 99.

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Outrun 2012

    Dion - - General Arcade Tech Help

    Post

    arcade-projects.com/forums/ind…8f1a98c32facdd7ae1c54d16d mobo is biostar g41d3+ v6.3. OS is windows, most likely xp. Surely not 7 or later. The game is PC game : outrun 2006 coast 2 coast, with custom gamepad i/o. There's a license file inside game folder that 'locked' with the i/o bd serial number. That's all i know.

  • Outrun 2012

    Dion - - General Arcade Tech Help

    Post

    Quote from stj: “interesting, but unclear - be nice to get the mobo part number - BIOSTAR?? also, where is the game? on the card - or a drive not in the foto? ” will get the p/n tomorrow. the game run from flash disk. you can see it besides psu under cables.

  • Outrun 2012

    Dion - - General Arcade Tech Help

    Post

    arcade-projects.com/forums/ind…8f1a98c32facdd7ae1c54d16d arcade-projects.com/forums/ind…8f1a98c32facdd7ae1c54d16d arcade-projects.com/forums/ind…8f1a98c32facdd7ae1c54d16d

  • Quote from stj: “here is a tip - dont buy shitty $10 chinese rachet crimpers. they will work, but they are optimised for specific terminals that arent really of interest to us. ” agree, but i bought it anyway since i don't know if it's good or not (buying online). It turned out it crappy but can work with a bit effort. could you also suggest which one is good? i also looking for this, especially for JST's.

  • Quote from xodaraP: “The problem with wick is it sticks when the solder cools and you end up making a huge mess with a job like this (I've tried something similar in the past) ” i actually have kind of same problem with wick. so i used coppers from new cable instead (the one that still shines like new). and flux it a lot, i never had it sticks again. btw, with poor heat, you can always use a real 60w solder, they're really kic* ***.

  • or just clean the legs first, then unbend them. use manual solder sucker, or a good solder wick with lots of flux.

  • JVS Emulator

    Dion - - Project Showcase

    Post

    Quote from bobbydilley: “Project Update: Unfortunately a negative update this time, I tried running it on a Raspberry Pi 1st gen today for the first time (had been developing on my mac, but target platform was obviously a Pi) and annoyingly it just doesn't work. I'm thinking that the PI can't process + reply fast enough and so its a speed issue. I will try on a better Pi2 or Pi3 later to see if that helps, or failing that attempt to make the code and linux distro more efficient. So if anyone tri…

  • with some code modification, yes, particularly, the time stamp for each chip. iirc, after sometime, i find out that these 'bad' card showed by 573 games, they're actually caused by 'slow' or you can say 'degraded' flash chip. since konami uses it's own timeout mechanism to verify the card. but actually, the chip itself is still okay, they're just 'slow' a bit. i can't say a lot, because i just have 2 flash card to play with. maybe some other bad card can actually have real bad flash chip inside.…

  • uhm... i don't quite understand what you mean. If you mean, can we use pcmcia adapter that comes with viper h/w. yes, we can. but you need to adapt the pcb footprint.

  • Hello, This is my own private tool, made sometime ago. It is arduino mega shield originally made, because of frustration at konami flash card rarity. Back then, i have 2 'Bad' cards which i hope to be able to check them properly, without having pulled the each flash chip out and test them individually with a programmer. At first, i tried to use this pci to pcmcia card to read them. arcade-projects.com/forums/ind…8f1a98c32facdd7ae1c54d16d But apparently, they need a special driver for each kind o…

  • it's not me who posted that hbbc cart photo, it's @Nem's.

  • arcade-projects.com/forums/ind…8f1a98c32facdd7ae1c54d16d

  • Quote from undamned: “Quote from Dion: “most likely they're Emifil or EMI Filter, made by TDK. the one with ferrite bead i know is from sega filter bd, which you can easily see the bead itself wounded by wires. don't know if there's a packaged one. some sega filter bd have values stated in manuals. the most common value are : 223 - for power lines 102 - for VGA signals 103 - for VCC line 680 - for I/O signals ” Do you happen to know what those numbers correlate to? I know ferrite beads are often…

  • most likely they're Emifil or EMI Filter, made by TDK. the one with ferrite bead i know is from sega filter bd, which you can easily see the bead itself wounded by wires. don't know if there's a packaged one. some sega filter bd have values stated in manuals. the most common value are : 223 - for power lines 102 - for VGA signals 103 - for VCC line 680 - for I/O signals

  • Konami System 573 help

    Dion - - General Jamma and pre-Jamma

    Post

    I have seen mod board like that. not quite sure how they works. as for cassette error, sometimes because of connector problem. clean it and re-plug.

  • i am afraid you can't use my device, since there's no known cd dumped. the installation routine usually reside on it. the best way to resurrect, like Mr T Guru said, is hand crafting the data, with MAME debugger's help.

  • Quote from defor: “by beeping do you mean the ding ding ding sound or a quack quack quack sound, or some other sound (I can get audio samples of these sound effects if needed)? Also I do know that BG3 will boot to a black screen unless an IO board AND the proper wiring to the analog board are in place- if brakes, throttle, steering aren't connected correctly or have come loose - or the IO board isn't powered up/on, the game will boot to a black screen... Any and all photos or details of the IO b…

  • Konami System 573 help

    Dion - - General Jamma and pre-Jamma

    Post

    Quote from DevoDave: “Now the beast fails to show anything on the screen. ” it should show something, this system is hard to fail, except for cdrom, and monitor. Quote: “It has a mod board, but it looks a quality unit. Percussion Freaks 9th. ” can you take photo of this mod board? Quote: “Do I need the cdrom and/or the i/o board installed to get it to boot? ” no, you don't need cdrom or i/o bd to get it boot.

  • i just see in mame source, that hbbc have (no cd) or not dumped yet. i guess what Mr T Guru said is right. If the game run did not run from cd, it is impossible to go into install mode.

  • Quote from chacal231077: “Quote from chacal231077: “Quote from Dion: “this system is notorious for having heat damage. especially, the playstation part. that mini fan at back is not enough. ” ” RE-Question saint.png The 246 & the 256 are equipped with thermal gap filler or thermal pad for the Heatsink ? What are the differences? ” it's not enough. it's a fact for sure.