Search Results

Search results 1-20 of 58.

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Quote from opt2not: “Did a thorough cleaning of the cart with a q-tip and isopropyl, still no change. These carts can be resurrected though, right? ” Of course they can be resurrected. Just have the Darksoft superbios installed and it will run forever. If you're worried about original game code, honestly @BlinG has two cps3's one with Japanese original and other with superbios. I've played both and don't notice any bit of difference between the two as far as gameplay.

  • Nanao MS-2930

    BMXer3s - - Monitor Help

    Post

    Bumping this thread. Would like to figure out what is causing this as well.

  • UD-USB Decoders

    BMXer3s - - Temple of the Undamned

    Post

    Got mine today 95-A22-C84-207-E-478-F-9-E4-E-4109184-EAACE.jpg

  • Home Arcade System

    BMXer3s - - RGB's lab

    Post

    Quote from opt2not: “Quote from moltomolto: “I've had my HAS hanging off the JAMMA edge of my CPS2 board for a few months now, is this a serious problem? The HAS sits a little lower than the CPS2 so I can't really put them both flat. That is unless anyone has recommendations for CPS2 rubber feet? ” Definitely. Over time your board may develop issues due to the pressure of bending the connector down. Either get extension cables, or make your CPS2 board sit vertically so that the strain isn't bend…

  • Hell0 friends

    BMXer3s - - Introduce Yourself!

    Post

    Welcome @]YaZ[ ! Good to see you on here man!

  • Quote from Wraith: “Fingers crossed hope it works out. Are you one of the French guys that came to DTN? ” This dude won the Gutter Trash tourney in the UK.

  • Totally forgot about this game haha. Say "NO" to drugs!!!

  • Home Arcade System

    BMXer3s - - RGB's lab

    Post

    Quote from Cat: “Does the Start and Select buttons on the XBox360 now become the 1 Player and Coin Buttons ? Is this how it works ? ” Yes it should be. That's how the layout is on my 360 TE fightstick.

  • Hey everyone

    BMXer3s - - Introduce Yourself!

    Post

    Welcome Aaron! aka @MunchiAZ!

  • Home Arcade System

    BMXer3s - - RGB's lab

    Post

    Quote from ChuChu Flamingo: “ for the mini din will this cable work? I would be connecting it to a GSCART switch. retro-access.com/products/fort…ds?variant=18593264926771 ” That cable will work perfectly. I use the same cable for my setup with a SCART to component adapter.

  • Quote from LawdVayduh: “I tested out the Brook Neo Geo adapter with a PS3 controller. It worked great in my limited testing. I didnt even realize that you initally plug your controller into it with USB and then you can disconnect the usb and use the PS3 controller wireless! Instructions say you can reassign buttons as well, but I didnt test that out. ” Does it work with 6-button games despite being a Neo Geo adapter?

  • Quote from SabreAZ: “out of curiosity, does the brook neogeo to ps4 adapters work? Since undamned's db15s are out of the limelight for a bit, im curious if they will work? ” That's actually a great question. Would like to hear if anyone has done any testing on this.

  • Home Arcade System

    BMXer3s - - RGB's lab

    Post

    Quote from jassin000: “Quote from BMXer3s: “I’m actually using a scart to component adapter and I’m currently using this one and it works very well- ” You are my new best friend! I fully support/approve/endorse this gear/setup, great job. ” The picture it outputs is absolutely stunning. I was very impressed.

  • Home Arcade System

    BMXer3s - - RGB's lab

    Post

    Quote from jassin000: “Quote from BMXer3s: “Finally got the HAS! ” That's a nicccce thick 8pin mini cable you got!Does it goto/end in Euro SCART? Did you buy it/find it online someplace?! PLZ share ” Here’s where I got the scart cable- retro-access.com/products/fort…-rgb-scart-cable-for-mods I’m actually using a scart to component adapter and I’m currently using this one and it works very well- rover.ebay.com/rover/0/0/0?mpr…Fulk%2Fitm%2F273178172012

  • Just got the HAS v4. This thing is just plain phenomenal. ELHR3131.jpg IMG-0553.jpg IMG-0555.jpg IMG-0559.jpg

  • Home Arcade System

    BMXer3s - - RGB's lab

    Post

    Finally got the HAS! Thank you RGB for an awesome product. It was worth the wait! IMG-0555.jpg IMG-0559.jpg

  • The finished product looks amazing!

  • Yo!

    BMXer3s - - Introduce Yourself!

    Post

    Welcome @Zitz! I used to race BMX for a long time. Used to have a Kastan and a Free Agent back in the day. Now currently have an Anarchy and a Speedco cruiser hanging up collecting dust LOL. I also am a Street Fighter III: 3rd Strike nut. Hence the name BMXer3s haha.

  • Home Arcade System

    BMXer3s - - RGB's lab

    Post

    Quote from RGB: “Quote from F34R: “Mine arrived via Fed Ex. Super fast shipping!! I should have it up and running sometime today. Super excited! ” Awesome, that's really fast! Make sure you read the HAS instruction manual before you start messing with it @msamiullah When did you submit your pre-order? I'm in the middle of the first batch (Jan-Feb pre-orders). ” Awesome to hear. I believe I was one of the last ones to pre order for that batch so I’m sure I got a little bit more time to wait. All …

  • Home Arcade System

    BMXer3s - - RGB's lab

    Post

    Quote from shorjewken: “I'm sorry I'm asking questions again, for those that got an e-mail back in June, have there been follow-up emails to those? The reason i ask is that it seems like the following batch is getting e-mails which makes me think I was forgotten. Totally understand all the thrash here but I want to make sure. Thanks. ” If you got an email back in June, that's the batch that is currently getting ready for shipping as we speak. It's right around the corner. Plus, a few posts earli…