Maybe if you concatenate the roms.
Gunforce conversion to Gunforce II (IREM M92)
This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.
-
-
The board can't address the space, it's not a case of not enough spaces for EPROMs, it's a case of not enough space can be read
-
So you have to check if there are already existing empty jumpers spaces not populated made on the board like on a few other M92 rom boards.
If not, you can check if you can trim the roms, or you'll have to use ugly wires then
-
You have to use wires because you need to connect the data lines that don't exist on that ROM board - that's why you see the spaghetti on the board above
-
Never said the info, I said the files
xodaraP wrote:
I'm sure @Apocalypse said it was impossible though. Someone is now saying the info came from him?
-
Never said it was impossible.
xodaraP wrote:
Indeed. If a Gunforce can be converted into RTL, it can work with the multi.
I'm sure @Apocalypse said it was impossible though. Someone is now saying the info came from him?
However I did say that wasn't easy due to the reason you mentioned earlier: missing address lines so wires have to be used.
A bit messy but doable.Looking for:
- OutRun boardset even untested or not working
- Sega Super Scaler hardware (Out Run, Model X, Model Y), even with faulty PCM chip
01010011 01000101 01000011 01010010 01000101 01010100 00100000 01001101 01000101 01001110 01010101 00100000 01000111 01010101 01011001 -
Apocalypse wrote:
Never said it was impossible.However I did say that wasn't easy due to the reason you mentioned earlier: missing address lines so wires have to be used.xodaraP wrote:
Indeed. If a Gunforce can be converted into RTL, it can work with the multi.
I'm sure @Apocalypse said it was impossible though. Someone is now saying the info came from him?
A bit messy but doable.
I more meant impossible in the sense that it's not a straightforward conversion and the amount of work required to pull it off makes it impossible for the majority of people
In saying that, if it can be done even with that much work that's still cool. -
I want to do it due to 2 reasons:
xtrasmiley wrote:
Easy to do in 2 steps:
Step 1: Sell Gunforce
Step 2: Buy Gunforce 2
Sorry man, I'm sure it can be done, but GF1 has a much smaller board, so it will be a lot of work, not sure it's worth it. Also a reason GF1 will probably not be a good donor for the upcoming multi M92.
Reason 1: I know It can be done, and I can do it.
Reason 2: Gunforce II is extremely rare to see, and very expensive if you can get one.
Best regards. -
I guess your best option is to follow the picture above. I don't think those who can do this are going to release the information publicly.
-
I can do nothing with such a picture... ... ...
xodaraP wrote:
I guess your best option is to follow the picture above. I don't think those who can do this are going to release the information publicly.
-
LOL
xodaraP wrote:
I guess your best option is to follow the picture above.
-
-Ace- wrote:
LOLxodaraP wrote:
I guess your best option is to follow the picture above.
?
Everyone wants the information handed to them, you can always do the work yourself and then document it for others. -
I just thought your comment to him was funny, peace- like anyone could utilize that picture. . .
-
-Ace- wrote:
I just thought your comment to him was funny, peace- like anyone could utilize that picture. . .
It shows you all the connections on the interconnect pins, you can see where most of the wires are going to on the chips.
Yes, you're going to have to do some research and trial and error but it's a lot better than starting with nothing at all. -
At least this one exists and works, i get messages all the time about stuff that does not work and does not exist (yet) demanding info
xodaraP wrote:
?-Ace- wrote:
LOLxodaraP wrote:
I guess your best option is to follow the picture above.
Everyone wants the information handed to them, you can always do the work yourself and then document it for others.
-
So is this saying I should refrain sending that message about turning my Quiz Chikyu Bouei Gun board into Guwange?
Hammy wrote:
i get messages all the time about stuff that does not work and does not exist (yet) demanding info
On the hunt for: Dinoking, Mushiking, Love & Berry, Egret 29, Grand Am Q25, Capcom New Concept 2, and Naomi guncabs. -
That's a common one, that's the sailor moon hardware again i guess...
rewrite wrote:
So is this saying I should refrain sending that message about turning my Quiz Chikyu Bouei Gun board into Guwange?Hammy wrote:
i get messages all the time about stuff that does not work and does not exist (yet) demanding info
Ordered one that style once for 200 brick years ago and it landed damaged in the mail, never bothered with it since, hardware too fragile / expensive to mess with. -
-
I wouldn't mind sharing the info but I don't have a Gunforce board handy to give proper details.
xodaraP wrote:
I guess your best option is to follow the picture above. I don't think those who can do this are going to release the information publicly.
It shouldn't be too hard to run wires for the missing address lines though, just by comparing with an other romboard.Looking for:
- OutRun boardset even untested or not working
- Sega Super Scaler hardware (Out Run, Model X, Model Y), even with faulty PCM chip
01010011 01000101 01000011 01010010 01000101 01010100 00100000 01001101 01000101 01001110 01010101 00100000 01000111 01010101 01011001
-
Share