Lemony Vengeance
Champion
Monitor Deposit Paid.
So we're up to two custom frames now? One for the K7000, and now one for the D9500?Yunus does his job correctly so the tube and chassis could be assembled perfectly on his custom frame.
@deibit, no.
All spares are NOS.
We talk about a D7000 (Tube and Frame) upgraded with the PD9500 electronic parts (chassis)
Earlier you implied that the tubes are used. When did they change to new?Correct, we found a stock in Brazil area.
Tube with no burns, rest is new and in 15/24/31 hz
@rewrite no.
The original frame was a D7000, who's the same used like the one in the K series by WG.
Concerning the chassis of the PD9500, i'm talking about the electronic parts... neck,main and remote boards who have been fixed on the frame of the D7000.
That's a real asshole thing to say, seeing as this project wouldn't even be off the ground, and you wouldn't be making money if it weren't for Rewrite.Now my best advice is to stop to do a lot of blabla and discuss in the wind wih a risk of a new mistmatching and in october/november, all could be done.
Let's Yunus to finish his job, the rest following with the people concerned.
I'm not, actually. I'm talking about the chassis, same as you. I can't tell if it's language barrier, your lack of knowledge, or you're just being pedantic. D9500 has a PD(tubesizehere)9500 main chassis PCB. We're talking about the same thing.You are focused on a D9500, where we talk about a PD9500 and where only the electronic part was keep... neck, remote and main board.
I'm not concerned about the sides. I'm concerned about the main chassis PCB does not have the same mounting pattern or general dimensions between k7000 and d9500.Concerning the D7000 frame, the people have confirmed the distance between the sides was exactly the same like the K7000 frame and also for the 4 screws in upfront.
You're not making sense in English. Earlier they were used but no burn. Today you say NOS. These are *very* different statements.Nothing was change concerning the tube, only the information was up-to-date.
Some guys in Brazil took NOS chassis, reverse engineered the data on the EPROM, and then edited it in a way to accept resolutions that it doesn't accept from the factory? That seems highly improbable. I believe you're being sold snake oil.The guys who do the retrofit confirm us to do the job correctly for the EPROM and other sync about the low res.
I am a "people concerned". You would not have a product to make money on if not for me. That comes off arrogant, but it's the truth of the matter and I'm uncertain how else to word it.Now my best advice is to stop to do a lot of blabla and discuss in the wind wih a risk of a new mistmatching and in october/november, all could be done.
Let's Yunus to finish his job, the rest following with the people concerned.
Funny that you say that not about the guy writing walls of text but about the guy who without his work this project wouldn't have even gotten off the ground.@‘Gaming.one’ don’t get discouraged, the majority of the deposits paid couldn’t be more elated and appreciative of the effort and transparency of this project. The Loudest ones in the room are always the weakest.
It's in the name, pal.@rewrong, you are wrong again.
Jeez man, is that really how you talk about people? Especially people who have gone out of their way to make something happen that you benefit from?@‘Gaming.one’ don’t get discouraged, the majority of the deposits paid couldn’t be more elated and appreciative of the effort and transparency of this project. The Loudest ones in the room are always the weakest.
You should not worry about logistics until there is a product to have logistics surrounding.But you are not concerned by the logistic, etc.. where i'm focused and the most important for me at this time.
Like I said before. You are trying to push the project along faster because it affects your bottom line. This is not a good thing for the people buying the product. It is only good for you.If i'm trying to close in the next months, that because the price concerning the logistic change and was not fixed yearly but monthly.
The guy took measurements of his own cabinet, used a color gun to find the correct colors, hunted down a k7000, the list goes on. He's not just a middle man, hes an integral part of this project next to Hursit. Listen to what he says.Concerning my side, i build this op like a group buying in offshore to kill a large costs and keep a friendly price.
If i didn't proceed on this way and want to making money, the price could be totally different... We talk around 3K EUR for a complete cab.
You miss the import taxes..follow the hs code could be around 20/30%, VAT was 20% also and don't include any marging.
For the monitors we resell a part of the lot to David the price we have purchased with the shipping added.
Where you think we have privilege, that's not the case, we move to do the job where anybody want to proceed really in Europe and other areas and waiting the cherry on the cake patiently.
The only win here is for everyone to receive what's he purchased, including me.
That's why i explain in my previous post, everyone has done his part of the job, including Rewrite and now it's time to move to the next step and don't waste our time with a lot of blabla and repeat always the same sound.
Next time try to have an helicopter view of the problem.
Just so you know, idgaf if your spinning the tubes yourself. So get off that high horse right now. I've contributed more to this project then you have at this point and I have zero dogs in the fight besides making sure my friends dont get stuck with a cabinet that isn't measured correctly. Myself and several folks have brought issues to the attention of rewrite behind the scenes and he helps Hursit with them. It's no secret I dislike Hursit and I don't care for Cereth either, but for you to put someone livelyhood on the line cause you have deadlines to meet is totally fucked.Buddy if you are so good move your ass to manage the logistic, financial, suppliers, importation and customer part of the op.After i see you are able to do we can talkI know that I said I wouldn't post again here.
I lied.
@Gaming.One is being a giant prick. @rewrite has bent over backwards to steer this shit show right numerous times. More so behind the scenes then most here know. Go fuck yourself pal.
That's it.