What's new
By:
Filters

Barn find Egret 2 project

Elfito69

Elfito69

Student
Joined
Jul 31, 2019
Messages
78
Reaction score
65
Location
San ysidro
i pick up this poor girl recently and it need a lot of work but the monitor and chassis works.

Ask you can see on the pictures , the jamma harness was cut off.
If any one can provide some pictures of the audio jst connector i will be very grateful
 

Attachments

  • IMG_20200615_233949.jpg
    IMG_20200615_233949.jpg
    921 KB · Views: 383
  • IMG_20200615_234017.jpg
    IMG_20200615_234017.jpg
    951.8 KB · Views: 318
  • IMG_20200615_234040.jpg
    IMG_20200615_234040.jpg
    884.6 KB · Views: 302
  • IMG_20200615_234117.jpg
    IMG_20200615_234117.jpg
    971.4 KB · Views: 376
I hope you got a tetanus shot before you touched that. Looks like a ton of work and hopefully that tube is still good.. but little at a time I am sure this can have potential.
 
BlinG said:
I hope you got a tetanus shot before you touched that. Looks like a ton of work and hopefully that tube is still good.. but little at a time I am sure this can have potential.
Click to expand...
the tube is good, it was replace by another toshiba whit the same curvature.
The original was fried
 
BlinG said:
I hope you got a tetanus shot before you touched that. Looks like a ton of work and hopefully that tube is still good.. but little at a time I am sure this can have potential.
Click to expand...
:thumbsup: :thumbsup: :thumbsup:
 
I started whit the bezel because it need more work.
The sun eat through the paint and made small cracks on the plastic, got most of it flatten out but still need to patch that hole
 

Attachments

  • IMG_20200616_015928.jpg
    IMG_20200616_015928.jpg
    975.9 KB · Views: 212
  • IMG_20200616_015326.jpg
    IMG_20200616_015326.jpg
    676.2 KB · Views: 197
Better to sand i all down and have the bottom blasted to see what rust is underneath and then repaint the whole thing :)

nice project!
 
Looking forward to watching this restore. Love to see a beautiful E2 brought back to life. Good luck, @Elfito69. And thanks for sharing the awesome (and helpful) restore photos, @Mrhide. Great work. Your skills are very impressive.
 
It looks great.

New graphics cp and paint would go a long way.

You can attach the wires to a new JAMMA female by following each wire to the JAMMA pinout diagram.

Good luck. I would be thrilled to find that in a barn.
 
hoagtech said:
Good luck. I would be thrilled to find that in a barn.
Click to expand...
i din't actually found it in a barn, i just named it that because it looks like one of those barn find classic cars :P

The operator did told me that they where on service a long ago and he stored them on a friends back yard, but rain and time got the best of them
 
Also was searching for a power supply cap kit but had no luck, so i went ahead and made a list

x1 560uf 180v @ c004
x4 10uf 50v @ c302,c007,c008,c003
x1 33uf 25v @ c015
x1 100uf 50v @ c011
x1 3300uf 10v @ c103
x1 4700uf 10v @ c101
x1 180uf 25v @ c202
x1 560uf 25v @ c301
x1 1000uf 25v @ c201



EDIT:
all caps are available on Digikey
 
Last edited:
You must log in or register to reply here.
Back
Top