Muchi Muchi Spork
Student
I'm going to compile some CPS1 hacks info here. It will take me a while to get it all in.
Street Smart (Final Fight hack for Street Fighter IICE hardware)
roms
https://mega.nz/#!FrBwTCSB!yaUoVqSxf4fc4lxidOm3wv3aHHHhgSEUFJIF7hLl3Wg
B-21 C-Board
91635B-2 B-Board - You can use 27C4000G roms for graphics or original mask roms from final fight
OR:
91634B-3 B Board - Use 27c4096G chips for graphics when using 91634B-3 board but you swap: top and bottom, swap 2 and 3, swap 1 and 2 then swap 3 and 4
91635B-2 B-Board roms in this order starting at position 3A:
5m
1m
7m
3m
Use S224B pal jed burned into gal16v8 then cut off top right pin (pin 20)
Cadillacs and Dinos hack for Street Fighter IICE
roms
https://mega.nz/#!VqgCGCCI!_sNf4kYzpNkEYUC_tH8h4Liz62jjeaNA6DUv_ew9vF0
only tested with dash mobo but probably works with other mobos
SF2CE setup works 91634B B board or 91635B
91634B board needs 27C4096G
91635B board needs 27C4000G
for 91634B place roms as labeled
for 91635B swap 2nd and 3rd and 6th and 7th
so you might need to burn gfx into 27C4000G chips for a 91635B B board
27C4096G for gfx and prg
27512 for 12a
MBM27C1000 on 11c and 12c (depends on jumpers)
Street Fighter II Rainbow
roms
https://mega.nz/#!UvZyhQBa!gmjK5Ol1GtHuX9dsBETAFEB3b8IWOjRyC82LCakoZ9M
just replace 3 program roms on SFIICE or SFII Hyper
1941 for Mercs B board (89624B-3) + SF2CE C board (CPS-B-21)
roms
https://mega.nz/#!ljBmDbZZ!7KFBOTNrP7Xp6TaGoNynI4BVEclmyFfMI6cDzUNMN1k
tested working using B board from Mercs (89624B-3)
protection C board CPS-B-21
motherboard type probably doesn't matter
depending on jumpers, you might need non-jedec type on program roms (27C301G, TC571001D)
sample roms need the same as above or it's missing sounds
others
27C010
27C512
note: program ran correctly in a test in SF2 board set (not 2CE) board but graphics were half missing
Ghouls n Ghosts (Japan) on Street Fighter IICE
roms
https://mega.nz/#!YmpAVKIQ!1RbEfCztqJ4TxhHegLsAe4DSpmEa0F-yaBHQFQu81wI
Japan board with 27C4096G graphics - keep graphics rom placement normal
Export B board with mask or 27C4000G graphics - in order top to bottom, swap 2nd and 3rd roms then swap 6th and 7th roms
The Punisher (China hack) on Street Fighter IICE
roms
https://mega.nz/#!53RXxayK!UCtUBRRkAxQFnvLL8mErVINu955jJIyPu1h4Pvh3W1w
instructions should be the same as above Ghouls hack
Warriors of Fate on Street Fighter IICE
roms
https://mega.nz/#!97pVRQKC!yybSi3SPoYn1ZSyAKbeZiO6wSi9hSUI_vxAetH23j6U
instructions should be the same as above Ghouls hack
I don't remember if it's a China-hacked graphics version or not
King of Dragons for Street Fighter IIWW B board + SF2CE C board (CPS-B-21)
roms
https://mega.nz/#!J6oHWACB!a1tRVnpPf52RBXiro58ptD-TrJ6PfkfNlQL1T-LEYOA
B board is 90629B-3 from SF2WW
C board is trusty "21 chip"
27C4096G for graphics - use Japan ver lower spots noted in mame source
Yes the heads are fixed
Dynasty Wars conversion
roms
https://mega.nz/#!U6wDzYoa!8SfcAGIPdnTeXQXcyJZ12F73yUXoLuEpK9axAq5YRqE
I don't have any notes on this one but the instructions will be very close to a Ghouls conversion, possibly with slightly more tricky graphics roms swapping
Street Fighter IICE etc. to Strider
roms
https://mega.nz/#!MqxXhSID!YlMFOFWBoNAzUGhkmFFZaIBY1Y4HhYnpV3uyM6b19V8
notes on this one are a mess, I no longer have the hardware to update it
you could make it (with these instructions) with a standard SF2CE setup or if you had the C board from SF2CE and an old 89624B B board from another game
if you want to put Strider on SF2CE hardware you should only need to program the "resale" chipset and the correct 1A pal/gal
there is included iirc a jed from the resale version and one from the older version, you might need to try both and check jammarcade.net if mine don't work for you
graphics roms might need swapped order depending on using a 27C4096G or 27C4000G based SF2CE B board
on the "89" type old B board (combined with 21 chip C board), just look to the the rom names from mame source for placement
if you have created it on the older 89 B boards you can swap your program to japan by burning in the "program to japan" folder contents in the rom upload
this is an old copy paste from the mame source that helps with loading, you can sometimes figure out the order to put the graphics roms by the order mame loads them
/* B-Board 89624B-2 */
ROM_START( strider )
ROM_REGION( CODE_SIZE, "maincpu", 0 ) /* 68000 code */
ROM_LOAD16_BYTE( "30.11f", 0x00000, 0x20000, CRC(da997474) SHA1(3e4ac98f9a6967d61899281b31c7de779723397b) )
ROM_LOAD16_BYTE( "35.11h", 0x00001, 0x20000, CRC(5463aaa3) SHA1(e2d07ec2d818e9a2e2d7a77ff0309ae4011c0083) )
ROM_LOAD16_BYTE( "31.12f", 0x40000, 0x20000, CRC(d20786db) SHA1(c9c75488e6bb37cfd0d56073faf87ff5713bc9a0) )
ROM_LOAD16_BYTE( "36.12h", 0x40001, 0x20000, CRC(21aa2863) SHA1(446dc9280630318deb423531210a4eedfb4adfa6) )
ROM_LOAD16_WORD_SWAP( "st-14.8h", 0x80000, 0x80000, CRC(9b3cfc0 SHA1(a7d7f270a097437affa845d80bed82a1fa87487 ) // in "32" socket
ROM_REGION( 0x400000, "gfx", 0 )
ROMX_LOAD( "st-2.8a", 0x000000, 0x80000, CRC(4eee9aea) SHA1(5e619fd5f3f1181e32a8fd9dbb4661d74ff8a484) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "6" socket
ROMX_LOAD( "st-11.10a", 0x000002, 0x80000, CRC(2d7f21e4) SHA1(593cec513de40ff802084d54313bb25a4561e25d) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "8" socket
ROMX_LOAD( "st-5.4a", 0x000004, 0x80000, CRC(7705aa46) SHA1(6cbfa30b2852fd117d117beefba434ce41d24c2f) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "2" socket
ROMX_LOAD( "st-9.6a", 0x000006, 0x80000, CRC(5b18b722) SHA1(cf71c62348ca6b404279e87a6686cb3a842eb381) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "4" socket
ROMX_LOAD( "st-1.7a", 0x200000, 0x80000, CRC(005f000b) SHA1(e6f65af7cc3295be9efaaded352e7ae6320b4133) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "5" socket
ROMX_LOAD( "st-10.9a", 0x200002, 0x80000, CRC(b9441519) SHA1(bb0926dc484dae4f64c5e5a6bce20afdc7aeba55) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "7" socket
ROMX_LOAD( "st-4.3a", 0x200004, 0x80000, CRC(b7d04e8b) SHA1(5c5a079baa694927c33d0e0c23e5ff09d6c9d985) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "1" socket
ROMX_LOAD( "st-8.5a", 0x200006, 0x80000, CRC(6b4713b4) SHA1(759b8b1fc7a5c4b00d74a27c2dd11667db44b09e) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "3" socket
ROM_REGION( 0x18000, "audiocpu", 0 ) /* 64k for the audio CPU (+banks) */
ROM_LOAD( "09.12b", 0x00000, 0x08000, CRC(2ed403bc) SHA1(4ce863ea40d789db5a7cfce91d2c7c720deb9be5) )
ROM_REGION( 0x40000, "oki", 0 ) /* Samples */
ROM_LOAD( "18.11c", 0x00000, 0x20000, CRC(4386bc80) SHA1(fb2b261995aeacfa13e7ee40b1a973dfb178f015) )
ROM_LOAD( "19.12c", 0x20000, 0x20000, CRC(444536d7) SHA1(a14f5de2f6b5b29ae5161dca1f8c08c566301a91) )
ROM_REGION( 0x0200, "bboardplds", 0 )
ROM_LOAD( "st24m1.1a", 0x0000, 0x0117, CRC(a80d357e) SHA1(4cb79c99c62c8300e694f4cd26f41dab7818f17f) )
/* B-Board 89624B-3 */
ROM_START( striderua )
ROM_REGION( CODE_SIZE, "maincpu", 0 ) /* 68000 code */
ROM_LOAD16_BYTE( "30.30", 0x00000, 0x20000, CRC(66aec273) SHA1(576b1e9062874e68d68f8725949c151509eb6d56) ) /* different CRC from strider but same label, pcb verified */
ROM_LOAD16_BYTE( "35.35", 0x00001, 0x20000, CRC(50e0e865) SHA1(201ef385c228c124ed9412002233a501ea514efd) ) /* different CRC from strider but same label, pcb verified */
ROM_LOAD16_BYTE( "31.31", 0x40000, 0x20000, CRC(eae93bd1) SHA1(b320a00b67ea3c7fffc6c37d57863163975f7b80) ) /* different CRC from strider but same label, pcb verified */
ROM_LOAD16_BYTE( "36.36", 0x40001, 0x20000, CRC(b904a31d) SHA1(5509d1024151eb8548fd1b29e6c0c95775c61364) ) /* different CRC from strider but same label, pcb verified */
ROM_LOAD16_WORD_SWAP( "st-14.8h", 0x80000, 0x80000, CRC(9b3cfc0 SHA1(a7d7f270a097437affa845d80bed82a1fa87487 ) // in "32" socket
ROM_REGION( 0x400000, "gfx", 0 )
ROMX_LOAD( "st-2.8a", 0x000000, 0x80000, CRC(4eee9aea) SHA1(5e619fd5f3f1181e32a8fd9dbb4661d74ff8a484) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "6" socket
ROMX_LOAD( "st-11.10a", 0x000002, 0x80000, CRC(2d7f21e4) SHA1(593cec513de40ff802084d54313bb25a4561e25d) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "8" socket
ROMX_LOAD( "st-5.4a", 0x000004, 0x80000, CRC(7705aa46) SHA1(6cbfa30b2852fd117d117beefba434ce41d24c2f) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "2" socket
ROMX_LOAD( "st-9.6a", 0x000006, 0x80000, CRC(5b18b722) SHA1(cf71c62348ca6b404279e87a6686cb3a842eb381) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "4" socket
ROMX_LOAD( "st-1.7a", 0x200000, 0x80000, CRC(005f000b) SHA1(e6f65af7cc3295be9efaaded352e7ae6320b4133) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "5" socket
ROMX_LOAD( "st-10.9a", 0x200002, 0x80000, CRC(b9441519) SHA1(bb0926dc484dae4f64c5e5a6bce20afdc7aeba55) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "7" socket
ROMX_LOAD( "st-4.3a", 0x200004, 0x80000, CRC(b7d04e8b) SHA1(5c5a079baa694927c33d0e0c23e5ff09d6c9d985) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "1" socket
ROMX_LOAD( "st-8.5a", 0x200006, 0x80000, CRC(6b4713b4) SHA1(759b8b1fc7a5c4b00d74a27c2dd11667db44b09e) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "3" socket
ROM_REGION( 0x8000, "stars", 0 )
ROM_COPY( "gfx", 0x000000, 0x000000, 0x8000 )
ROM_REGION( 0x18000, "audiocpu", 0 ) /* 64k for the audio CPU (+banks) */
ROM_LOAD( "09.9", 0x00000, 0x08000, CRC(08d63519) SHA1(c120ecfe25c3c50bc51bc7d5a9ef1c8ca6591240) ) /* different CRC from strider but same label, pcb verified */
ROM_CONTINUE( 0x10000, 0x08000 )
ROM_REGION( 0x40000, "oki", 0 ) /* Samples */
ROM_LOAD( "18.11c", 0x00000, 0x20000, CRC(4386bc80) SHA1(fb2b261995aeacfa13e7ee40b1a973dfb178f015) )
ROM_LOAD( "19.12c", 0x20000, 0x20000, CRC(444536d7) SHA1(a14f5de2f6b5b29ae5161dca1f8c08c566301a91) )
ROM_REGION( 0x0200, "aboardplds", 0 )
ROM_LOAD( "buf1", 0x0000, 0x0117, CRC(eb122de7) SHA1(b26b5bfe258e3e184f069719f9fd008d6b8f6b9b) )
ROM_LOAD( "ioa1", 0x0000, 0x0117, CRC(59c7ee3b) SHA1(fbb887c5b4f5cb8df77cec710eaac2985bc482a6) )
ROM_LOAD( "prg1", 0x0000, 0x0117, CRC(f1129744) SHA1(a5300f301c1a08a7da768f0773fa0fe3f683b237) )
ROM_LOAD( "rom1", 0x0000, 0x0117, CRC(41dc73b9) SHA1(7d4c9f1693c821fbf84e32dd6ef62ddf14967845) )
ROM_LOAD( "sou1", 0x0000, 0x0117, CRC(84f4b2fe) SHA1(dcc9e86cc36316fe42eace02d6df75d08bc8bb6d) )
ROM_REGION( 0x0200, "bboardplds", 0 )
ROM_LOAD( "st24b2.1a", 0x0000, 0x0117, NO_DUMP )
ROM_LOAD( "lwio.11e", 0x0000, 0x0117, CRC(ad52b90c) SHA1(f0fd6aeea515ee449320fe15684e6b3ab7f97bf4) )
ROM_END
more coming
Street Smart (Final Fight hack for Street Fighter IICE hardware)
roms
https://mega.nz/#!FrBwTCSB!yaUoVqSxf4fc4lxidOm3wv3aHHHhgSEUFJIF7hLl3Wg
B-21 C-Board
91635B-2 B-Board - You can use 27C4000G roms for graphics or original mask roms from final fight
OR:
91634B-3 B Board - Use 27c4096G chips for graphics when using 91634B-3 board but you swap: top and bottom, swap 2 and 3, swap 1 and 2 then swap 3 and 4
91635B-2 B-Board roms in this order starting at position 3A:
5m
1m
7m
3m
Use S224B pal jed burned into gal16v8 then cut off top right pin (pin 20)
Cadillacs and Dinos hack for Street Fighter IICE
roms
https://mega.nz/#!VqgCGCCI!_sNf4kYzpNkEYUC_tH8h4Liz62jjeaNA6DUv_ew9vF0
only tested with dash mobo but probably works with other mobos
SF2CE setup works 91634B B board or 91635B
91634B board needs 27C4096G
91635B board needs 27C4000G
for 91634B place roms as labeled
for 91635B swap 2nd and 3rd and 6th and 7th
so you might need to burn gfx into 27C4000G chips for a 91635B B board
27C4096G for gfx and prg
27512 for 12a
MBM27C1000 on 11c and 12c (depends on jumpers)
Street Fighter II Rainbow
roms
https://mega.nz/#!UvZyhQBa!gmjK5Ol1GtHuX9dsBETAFEB3b8IWOjRyC82LCakoZ9M
just replace 3 program roms on SFIICE or SFII Hyper
1941 for Mercs B board (89624B-3) + SF2CE C board (CPS-B-21)
roms
https://mega.nz/#!ljBmDbZZ!7KFBOTNrP7Xp6TaGoNynI4BVEclmyFfMI6cDzUNMN1k
tested working using B board from Mercs (89624B-3)
protection C board CPS-B-21
motherboard type probably doesn't matter
depending on jumpers, you might need non-jedec type on program roms (27C301G, TC571001D)
sample roms need the same as above or it's missing sounds
others
27C010
27C512
note: program ran correctly in a test in SF2 board set (not 2CE) board but graphics were half missing
Ghouls n Ghosts (Japan) on Street Fighter IICE
roms
https://mega.nz/#!YmpAVKIQ!1RbEfCztqJ4TxhHegLsAe4DSpmEa0F-yaBHQFQu81wI
Japan board with 27C4096G graphics - keep graphics rom placement normal
Export B board with mask or 27C4000G graphics - in order top to bottom, swap 2nd and 3rd roms then swap 6th and 7th roms
The Punisher (China hack) on Street Fighter IICE
roms
https://mega.nz/#!53RXxayK!UCtUBRRkAxQFnvLL8mErVINu955jJIyPu1h4Pvh3W1w
instructions should be the same as above Ghouls hack
Warriors of Fate on Street Fighter IICE
roms
https://mega.nz/#!97pVRQKC!yybSi3SPoYn1ZSyAKbeZiO6wSi9hSUI_vxAetH23j6U
instructions should be the same as above Ghouls hack
I don't remember if it's a China-hacked graphics version or not
King of Dragons for Street Fighter IIWW B board + SF2CE C board (CPS-B-21)
roms
https://mega.nz/#!J6oHWACB!a1tRVnpPf52RBXiro58ptD-TrJ6PfkfNlQL1T-LEYOA
B board is 90629B-3 from SF2WW
C board is trusty "21 chip"
27C4096G for graphics - use Japan ver lower spots noted in mame source
Yes the heads are fixed
Dynasty Wars conversion
roms
https://mega.nz/#!U6wDzYoa!8SfcAGIPdnTeXQXcyJZ12F73yUXoLuEpK9axAq5YRqE
I don't have any notes on this one but the instructions will be very close to a Ghouls conversion, possibly with slightly more tricky graphics roms swapping
Street Fighter IICE etc. to Strider
roms
https://mega.nz/#!MqxXhSID!YlMFOFWBoNAzUGhkmFFZaIBY1Y4HhYnpV3uyM6b19V8
notes on this one are a mess, I no longer have the hardware to update it
you could make it (with these instructions) with a standard SF2CE setup or if you had the C board from SF2CE and an old 89624B B board from another game
if you want to put Strider on SF2CE hardware you should only need to program the "resale" chipset and the correct 1A pal/gal
there is included iirc a jed from the resale version and one from the older version, you might need to try both and check jammarcade.net if mine don't work for you
graphics roms might need swapped order depending on using a 27C4096G or 27C4000G based SF2CE B board
on the "89" type old B board (combined with 21 chip C board), just look to the the rom names from mame source for placement
if you have created it on the older 89 B boards you can swap your program to japan by burning in the "program to japan" folder contents in the rom upload
this is an old copy paste from the mame source that helps with loading, you can sometimes figure out the order to put the graphics roms by the order mame loads them
/* B-Board 89624B-2 */
ROM_START( strider )
ROM_REGION( CODE_SIZE, "maincpu", 0 ) /* 68000 code */
ROM_LOAD16_BYTE( "30.11f", 0x00000, 0x20000, CRC(da997474) SHA1(3e4ac98f9a6967d61899281b31c7de779723397b) )
ROM_LOAD16_BYTE( "35.11h", 0x00001, 0x20000, CRC(5463aaa3) SHA1(e2d07ec2d818e9a2e2d7a77ff0309ae4011c0083) )
ROM_LOAD16_BYTE( "31.12f", 0x40000, 0x20000, CRC(d20786db) SHA1(c9c75488e6bb37cfd0d56073faf87ff5713bc9a0) )
ROM_LOAD16_BYTE( "36.12h", 0x40001, 0x20000, CRC(21aa2863) SHA1(446dc9280630318deb423531210a4eedfb4adfa6) )
ROM_LOAD16_WORD_SWAP( "st-14.8h", 0x80000, 0x80000, CRC(9b3cfc0 SHA1(a7d7f270a097437affa845d80bed82a1fa87487 ) // in "32" socket
ROM_REGION( 0x400000, "gfx", 0 )
ROMX_LOAD( "st-2.8a", 0x000000, 0x80000, CRC(4eee9aea) SHA1(5e619fd5f3f1181e32a8fd9dbb4661d74ff8a484) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "6" socket
ROMX_LOAD( "st-11.10a", 0x000002, 0x80000, CRC(2d7f21e4) SHA1(593cec513de40ff802084d54313bb25a4561e25d) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "8" socket
ROMX_LOAD( "st-5.4a", 0x000004, 0x80000, CRC(7705aa46) SHA1(6cbfa30b2852fd117d117beefba434ce41d24c2f) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "2" socket
ROMX_LOAD( "st-9.6a", 0x000006, 0x80000, CRC(5b18b722) SHA1(cf71c62348ca6b404279e87a6686cb3a842eb381) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "4" socket
ROMX_LOAD( "st-1.7a", 0x200000, 0x80000, CRC(005f000b) SHA1(e6f65af7cc3295be9efaaded352e7ae6320b4133) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "5" socket
ROMX_LOAD( "st-10.9a", 0x200002, 0x80000, CRC(b9441519) SHA1(bb0926dc484dae4f64c5e5a6bce20afdc7aeba55) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "7" socket
ROMX_LOAD( "st-4.3a", 0x200004, 0x80000, CRC(b7d04e8b) SHA1(5c5a079baa694927c33d0e0c23e5ff09d6c9d985) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "1" socket
ROMX_LOAD( "st-8.5a", 0x200006, 0x80000, CRC(6b4713b4) SHA1(759b8b1fc7a5c4b00d74a27c2dd11667db44b09e) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "3" socket
ROM_REGION( 0x18000, "audiocpu", 0 ) /* 64k for the audio CPU (+banks) */
ROM_LOAD( "09.12b", 0x00000, 0x08000, CRC(2ed403bc) SHA1(4ce863ea40d789db5a7cfce91d2c7c720deb9be5) )
ROM_REGION( 0x40000, "oki", 0 ) /* Samples */
ROM_LOAD( "18.11c", 0x00000, 0x20000, CRC(4386bc80) SHA1(fb2b261995aeacfa13e7ee40b1a973dfb178f015) )
ROM_LOAD( "19.12c", 0x20000, 0x20000, CRC(444536d7) SHA1(a14f5de2f6b5b29ae5161dca1f8c08c566301a91) )
ROM_REGION( 0x0200, "bboardplds", 0 )
ROM_LOAD( "st24m1.1a", 0x0000, 0x0117, CRC(a80d357e) SHA1(4cb79c99c62c8300e694f4cd26f41dab7818f17f) )
/* B-Board 89624B-3 */
ROM_START( striderua )
ROM_REGION( CODE_SIZE, "maincpu", 0 ) /* 68000 code */
ROM_LOAD16_BYTE( "30.30", 0x00000, 0x20000, CRC(66aec273) SHA1(576b1e9062874e68d68f8725949c151509eb6d56) ) /* different CRC from strider but same label, pcb verified */
ROM_LOAD16_BYTE( "35.35", 0x00001, 0x20000, CRC(50e0e865) SHA1(201ef385c228c124ed9412002233a501ea514efd) ) /* different CRC from strider but same label, pcb verified */
ROM_LOAD16_BYTE( "31.31", 0x40000, 0x20000, CRC(eae93bd1) SHA1(b320a00b67ea3c7fffc6c37d57863163975f7b80) ) /* different CRC from strider but same label, pcb verified */
ROM_LOAD16_BYTE( "36.36", 0x40001, 0x20000, CRC(b904a31d) SHA1(5509d1024151eb8548fd1b29e6c0c95775c61364) ) /* different CRC from strider but same label, pcb verified */
ROM_LOAD16_WORD_SWAP( "st-14.8h", 0x80000, 0x80000, CRC(9b3cfc0 SHA1(a7d7f270a097437affa845d80bed82a1fa87487 ) // in "32" socket
ROM_REGION( 0x400000, "gfx", 0 )
ROMX_LOAD( "st-2.8a", 0x000000, 0x80000, CRC(4eee9aea) SHA1(5e619fd5f3f1181e32a8fd9dbb4661d74ff8a484) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "6" socket
ROMX_LOAD( "st-11.10a", 0x000002, 0x80000, CRC(2d7f21e4) SHA1(593cec513de40ff802084d54313bb25a4561e25d) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "8" socket
ROMX_LOAD( "st-5.4a", 0x000004, 0x80000, CRC(7705aa46) SHA1(6cbfa30b2852fd117d117beefba434ce41d24c2f) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "2" socket
ROMX_LOAD( "st-9.6a", 0x000006, 0x80000, CRC(5b18b722) SHA1(cf71c62348ca6b404279e87a6686cb3a842eb381) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "4" socket
ROMX_LOAD( "st-1.7a", 0x200000, 0x80000, CRC(005f000b) SHA1(e6f65af7cc3295be9efaaded352e7ae6320b4133) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "5" socket
ROMX_LOAD( "st-10.9a", 0x200002, 0x80000, CRC(b9441519) SHA1(bb0926dc484dae4f64c5e5a6bce20afdc7aeba55) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "7" socket
ROMX_LOAD( "st-4.3a", 0x200004, 0x80000, CRC(b7d04e8b) SHA1(5c5a079baa694927c33d0e0c23e5ff09d6c9d985) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "1" socket
ROMX_LOAD( "st-8.5a", 0x200006, 0x80000, CRC(6b4713b4) SHA1(759b8b1fc7a5c4b00d74a27c2dd11667db44b09e) , ROM_GROUPWORD | ROM_SKIP(6) ) // in "3" socket
ROM_REGION( 0x8000, "stars", 0 )
ROM_COPY( "gfx", 0x000000, 0x000000, 0x8000 )
ROM_REGION( 0x18000, "audiocpu", 0 ) /* 64k for the audio CPU (+banks) */
ROM_LOAD( "09.9", 0x00000, 0x08000, CRC(08d63519) SHA1(c120ecfe25c3c50bc51bc7d5a9ef1c8ca6591240) ) /* different CRC from strider but same label, pcb verified */
ROM_CONTINUE( 0x10000, 0x08000 )
ROM_REGION( 0x40000, "oki", 0 ) /* Samples */
ROM_LOAD( "18.11c", 0x00000, 0x20000, CRC(4386bc80) SHA1(fb2b261995aeacfa13e7ee40b1a973dfb178f015) )
ROM_LOAD( "19.12c", 0x20000, 0x20000, CRC(444536d7) SHA1(a14f5de2f6b5b29ae5161dca1f8c08c566301a91) )
ROM_REGION( 0x0200, "aboardplds", 0 )
ROM_LOAD( "buf1", 0x0000, 0x0117, CRC(eb122de7) SHA1(b26b5bfe258e3e184f069719f9fd008d6b8f6b9b) )
ROM_LOAD( "ioa1", 0x0000, 0x0117, CRC(59c7ee3b) SHA1(fbb887c5b4f5cb8df77cec710eaac2985bc482a6) )
ROM_LOAD( "prg1", 0x0000, 0x0117, CRC(f1129744) SHA1(a5300f301c1a08a7da768f0773fa0fe3f683b237) )
ROM_LOAD( "rom1", 0x0000, 0x0117, CRC(41dc73b9) SHA1(7d4c9f1693c821fbf84e32dd6ef62ddf14967845) )
ROM_LOAD( "sou1", 0x0000, 0x0117, CRC(84f4b2fe) SHA1(dcc9e86cc36316fe42eace02d6df75d08bc8bb6d) )
ROM_REGION( 0x0200, "bboardplds", 0 )
ROM_LOAD( "st24b2.1a", 0x0000, 0x0117, NO_DUMP )
ROM_LOAD( "lwio.11e", 0x0000, 0x0117, CRC(ad52b90c) SHA1(f0fd6aeea515ee449320fe15684e6b3ab7f97bf4) )
ROM_END
more coming
Last edited: