Search results

I don’t think it will be an issue - it isn’t much taller than the connector so it’s not really adding much to the height. Have top finished just trying to work on a slide switch now.

Ok the main box is complete. Nice tight fit around the connector. Everything is so carefully dialed in that I can probably remove the recessed screw holes entirely because it’s a very nice friction fit. I also increased the thickness of the base so that it sits flat on the shelf behind the Marty...

Plan is to have a large plastic slide switch with a little hole for the real switch to go into, this would protrude through the lid to allow to slide on/off. I’m having fun learning - this is the first 3D print I have designed myself from the ground up.

I have started creating a case for the memory expansion. I have the footprint done with countersunk screw holes coming up through the bottom. I just need to finishing tightening up around the hole for the connector and then make the snap on lid. I will upload when finished. I hated leaving it...

Does it just need a recap or what?

Has anyone ever created a 3D printed case for the RAM Expansion yet? I recently purchased one of the RAM boards, but I don't like the idea of leaving the bare unprotected board plugged into my Marty.

Hi all I’m in need of a good condition B board shell top (willing to buy top and bottom). The one I have on my Multi is pretty beat up (cracks/deep scratches). I don’t want to take apart a functional B board for it so I am hoping someone has one to sell from a dead board. Any color is fine.

Thanks I used the Arthrimus Quick Solder Bus, I guess I’ll try removing it and doing a straight wiring setup. Are there alternate points I could use to test continuity for the keyharness wires? Edit: Awesome! I reflowed the solder for the Setup 1 and Setup 2 points in the Arthrimus Quick Solder...

would the key writing wires affect it not auto reset after loading a game?

yes used my desoldering station to pull it out whole, came out easy also i did realize that i dont need to remove the sd card for the hacks, if i select them and let it flash the game/key then power the cps2 off then on they play perfectly is there a specific amount of time required to short...

So I had a cps2 with a dead battery, it wouldnt boot but the battery still had some voltage, so i shorted exc5 but i still get a purple screen after it flashes a game and writes a key, however if the game is a hack like MvC Unlocked or Vampire Savior Hack then if I reboot the cp2 without the sd...

yea i replaced my fan with a pwm fan and a pwm fan controller that has a temp sensor, it automatically adjusts speed based on internal temps, its usually dead silent

i just got mine from twisted quarter last week, it came in fast and is working great with my HAS and CPS2 Multi

Hi all, installing a Darksoft Multi in a unit that I'd probably grade C or C-. The A-board shell looks good and the bottom half of the B-board shell looks good, but the colored B-board top shell is pretty ugly - a lot of scratches and marks that wont come off. I've found a very close matching...

Yes! Mine is also a Hispanic board but with a green shell instead of the typical orange - weird. Thanks for the tips, the 96 pin connectors just came in today - time to get to work! Edit: Thanks for your help dude, just got my CPS2 multi fully setup and working great. Adding the CN5 and CN6...

I would like to purchase one of these as well. Really would like the ability to use my HAS along with CPS2 Multi LCD Holster!

any idea why some of these revision 7 boards are missing CN5 and CN6? I had read about revision 3 boards missing CN6 and some rom sockets but always thought revision 7 was supposed to be plug and play

was your board a hispanic board? I'm running into the same issue with a Hispanic Marvel VS Capcom. The board is Rev 7 with the G PAL which I thought was supposed to be easy install, but not mine apparently. I'm waiting on the headers to arrive, and I'm not too concerned about the install. I've...

Have any invoices gone out for HAS preorders yet? I keep checking my email but I don’t know what address it will come from and I get a lot of junk so I am scared I’ll miss it. Q1 ended with March right? Has there been a delay?

I’ve been considering installing one of these fans along with this temp based fan controller (pic and link below) in my CPS2 once my Darksoft Multi arrives. Anyone have experience with these cheap temp probe based Pwm controllers? Icstation 12V 4 Wire PWM PC Case CPU Fan Thermostat Speed...