Search results

  1. S

    MV-1C Not Showing a Picture Correctly

    Thanks for your help and time. I'll definitely clean the JAMMA edge.
  2. S

    MV-1C Not Showing a Picture Correctly

    I just tried switching the blue and green cables and got no signal so switching them wasn't it as Sync is on the green cable. Sync is on 75 ohms. Glad the power is fine though. Maybe the JAMMA edge is dirty then as I try to get a tight fit every time I plug the connector to the board.
  3. S

    MV-1C Not Showing a Picture Correctly

    Well, I said the power supply because I can't think of what might have caused the weirdness in the video in my first post. If anyone has other thoughts, I'd hear them. I don't have a lot of experience so I was guessing on what the issue can be.
  4. S

    MV-1C Not Showing a Picture Correctly

    Correct. It worked just fine.
  5. S

    MV-1C Not Showing a Picture Correctly

    So I tried it again with a CPS2 and the MV-1C and everything went fine on the first attempt. I wonder if my psu is the issue then.
  6. S

    MV-1C Not Showing a Picture Correctly

    I don't have my setup with me as I go between two places during the week so I'm going to have to test this weekend as well. Thanks nem for helping. Next week, I'll report my findings.
  7. S

    MV-1C Not Showing a Picture Correctly

    I confirmed my CPS2 worked in this setup a couple of months ago but I would need to test my CPS2 again to see if anything changed. I won't be able to test until this weekend. If it doesn't work, should I assume the minigun isn't working or could it be a power issue? I ask because one time I...
  8. S

    MV-1C Not Showing a Picture Correctly

    Does anyone know what's happening?
  9. S

    MV-1C Not Showing a Picture Correctly

    I have a MV-1C that isn't properly showing a picture. From the below video, you can see a part of the title screen is shown in the bottom right corner. I tested it in late August or early September and it worked fine with no issues. My setup is the Minigun supergun mini din 9 ver. from...
  10. S

    CPS2 multi question

    I just found out that I'm in the same boat lol.
  11. S

    CPS3 Acrylic Case on Taobao

    Yes go to the discord link either in the RetroRGB post or on garou81's post above and look on the left where it shows different threads. You will see a CPS3 thread with an order form.
  12. S

    WTB : 100¥ coins

    If that's the case, I'd hit up some A-P users living in Japan to see if they can send the coins.
  13. S

    WTB : 100¥ coins

    You can see if your bank will do a currency exchange to get the coins. If not, you can look on yahoo auctions for older coins: https://auctions.yahoo.co.jp/category/list/2084036913/
  14. S

    CPS3 Acrylic Case on Taobao

    That should work for everyone. I made an edit to my post.
  15. S

    CPS3 Acrylic Case on Taobao

    Jasen from JasensCustoms is doing another CPS3 metal case for those who are interested and go to the CPS3 thread after clicking on the discord link: https://www.retrorgb.com/one-last-run-jasens-customs-cps2-metal-enclosure-pre-orders-opening.html
  16. S

    Jasen's amazing case is doing ONE last run

    Sorry about that.
  17. S

    Jasen's amazing case is doing ONE last run

    @Darksoft, what's the best way for Jasen from JasenCustoms to contact you? He said on 8/21 that he reached out to you to see if you will give him the schematics of the tiny dipswitch PCB for the Ultra Simms setup. He plans to design one that has mounting tabs and relocate the pinheader to the back.
  18. S

    Jasen's amazing case is doing ONE last run

    Jasen said he was going to make something that bolts into the case so that only the dipswitch is visible.
  19. S

    [WTB] Jasen's Customs CPS2 case - Longshot!

    Glad you was able to buy one in time.
  20. S

    Jasen's amazing case is doing ONE last run

    I asked him about the possibly of including mounting for the DIP switch bank.
Top