Search results

  1. hernan43

    SuperGun Power Supply Question

    This is the rule of thumb I've always heard and abide by.
  2. hernan43

    Mean Well RT-50A case

    I am using a Mean Well RT-50A PSU to run my NeoGeo and PGM. This case is just keeping me from zapping my fingers off on bare terminals or going nuts due to not having a power switch. It was intended to be used with heat set inserts but you could just use fat screws to secure the top. Design...
  3. hernan43

    Suzo Happ Power Pro Cover

    I have a Suzo Happ Power Pro 110V PSU(80-0064-00): https://na.suzohapp.com/products/power_supplies/80-0064-00 I've started a VERY WIP cover for it here: https://www.thingiverse.com/thing:4950743 Originally it was designed for a snap in IEC socket like this one...
  4. hernan43

    Naomi mounting feet

    This post had very good timing for me as I was quite literally looking for this this morning and here it is.
  5. hernan43

    OpenJVS - JVS Emulator

    I’m the same boat. Will have to keep my eyes peeled for the next go around.
  6. hernan43

    Minigun Supergun - An Open Source Supergun

    Well that makes me feel better! :-)
  7. hernan43

    Minigun Supergun - An Open Source Supergun

    Probably a dumb question but I assembled a v2.5 and left the headphone jack unpopulated. That particular part is coming just not yet. I had everything else. I do not get audio from this board. Is this because the headphone jack is missing or do I just need to go back re-re-re-check everything...
  8. hernan43

    3D printed cover for Mean Well MWP-606 [STL inside]

    If you are desperate you can use a service like Shapeways or 3dhubs. My only issue with them is that it is sort of pricey for what you get. My library does 3d printing on demand for $0.10 per gram I think. It might be worth it to see if you have something similar nearby if you can't find anyone...
  9. hernan43

    Motherboard issues TRAP14 error

    Yeah this board definitely has battery leakage damage on it. Not a ton, but enough. I'm going to see if the ebay seller is willing to do anything. If not then I might _attempt_ to fix it myself though I am not an electronomist so I have little faith. :-)
  10. hernan43

    Motherboard issues TRAP14 error

    I recently got a PGM motherboard on eBay. It had battery damage on it, however, it worked fine. I was able to play games on it. Sound, video, everything worked great. A few days later(today) it booted with an unusual "TRAP 14" error. The error shows up both if there is no cart or if there is a...
  11. hernan43

    3D printable Mean Well MWP-606 cover

    Heh, I really think the knob/extension is a good idea. I adjusted the voltage on mine and was sweating bullets as I (mostly) blindly maneuvered the screwdriver down that hole. Luckily there is no high voltage in that specific spot, but yeah i was in full on fear mode.
  12. hernan43

    3D printable Mean Well MWP-606 cover

    How did you make the knob?
  13. hernan43

    3D printable Mean Well MWP-606 cover

    Thanks! I absolutely am impressed with your design. I have some of the parts needed for it and I have not ruled out making one. It really was an impressive piece of design work.
  14. hernan43

    3D printable Mean Well MWP-606 cover

    Hi all, Just wanted to share a modest 3D printable cover I made for my Mean Well MWP-606. I use a minigun supergun that I like to operate on my desk out in the open. I power it off of an MWP-606 power supply. Not wanting to electrocute myself when I wasn't paying attention, I went looking for...
  15. hernan43

    Minigun Supergun - An Open Source Supergun

    So I did end up 3D printing a case and you are right. You could club a baby seal with this thing.
  16. hernan43

    Minigun Supergun - An Open Source Supergun

    Oooh thanks for the tip! I didn't realize the design had been updated for the current revision.
  17. hernan43

    Minigun Supergun - An Open Source Supergun

    Adding myself to the list of people that have built one of these. I noticed a couple weird things. First I mounted the LED correctly which has never happened before, and despite my best efforts the minigun worked on the first try. Very strange! :-) Thank you for all the hard work on this it is...
  18. hernan43

    Home Arcade System

    Yeah my voltmeter went udders up on the second day, but my HAS has been working like a champ. It is ULTRA nice.
  19. hernan43

    Home Arcade System

    I used a plastic storage container that fits the PSU. I drilled holes in it for the wires to pass through. It works superbly. It keeps my hands protected when I'm digging around inside my arcade setup.
  20. hernan43

    Home Arcade System

    This is what I bought: https://www.parts-express.com/6-ft-ac-power-cord-to-spade-lugs-black-18-3--110-101
Top