Search results

  1. Mukuro_W

    Capcom Big Blue Q-Sound audio issue

    I have both Capcom amp inside Capcom candy and also installed just the same sega amp on Egret 2 and it is just awesome too, it comes with volume pot and for sure have enough power to drive those capcom-yamaha speakers (the same as q25 and Impress cab)
  2. Mukuro_W

    MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

    Another user here had the same problem, he cured this by putting some 120 ohm resistors on rgb lines at jamma connector.
  3. Mukuro_W

    MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

    Yes it Is just what I did, had to set the gain pots to obtain an easy setup from mvs cps2 and the other jamma board to mistercade just using the contrast pot only. To make it easy I put the contrast pot to max to obtain an absolutely sharp and brilliant colors for jamma pcbs and just turn...
  4. Mukuro_W

    MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

    Have you ever released this adapter, maybe can fix all rgb gains issues on my cab
  5. Mukuro_W

    MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

    Are there any software option for RGB v. Peak? Maybe I must create a new sd just using the image and config as ofiicial guide since also cps1 running at same level of the MVS on this cab with this setting.
  6. Mukuro_W

    MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

    First of all thank you for your support, to get a good picture I had to put down the gains and turn up a bit the G2, now I got a pretty awesome picture with mistercade but a not brilliant picture with snk MVS board. On the Jamma connector I have 0.450Kohm from green, red and blue to video...
  7. Mukuro_W

    MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

    Got the mistercade complete kit, it Is awesome but I have a very weird issue on Egret II, here the rgb colors are ovesaturated and bleeding to the right, the Nanao ms9 inside not have any issues with MVS or CPS2 jamma boards, perfect colors and sharpness. The same mistercade kit working...
  8. Mukuro_W

    Sony BVM 20E1U / BVM-20E1U tube swap

    Please show a picture of the pcb and the Elena cap wich was the issue. This should be usefull not only for E1 but also for F1 .
  9. Mukuro_W

    CPS1 Multi. Official Thread

    While I'm waiting for my unit to arrive I have a question, cps1 games are almost not amplifued stereo but some just were mono amplified to jamma only, for example ghouls n ghost, is it possible to have all in stereo?
  10. Mukuro_W

    PVM Image Waving Issue Exclusively with Supergun

    PVM 1444qm , 1442qm, 1440qm and 2040 series all same issues, Fe board (psu board) replace c613 4.7uf 250v ASAP A board (main board) replace C551 1000uf 16v C518 470uf 16v C632 22uf 250v (high ripple) Check D504 and D505 for cold solder joints, those diodes are near the flyback, on thr...
  11. Mukuro_W

    Weird stripe on monitor - help?

    Those are v. Blanking lines plus v linearity issue, you should locate the v. Out ic and look for pcb crack and or dry somder joints or leaking cap in that area.
  12. Mukuro_W

    Taito Egret II illumination panel

    Hi. Looking for an illumination panel for Egret II, genuine or repro.
  13. Mukuro_W

    Official: CPS1 (CPS1.5) Multi by Darksoft/Apocalypse - Interest Check Thread

    No I want a CRT for game select, I hate lcd word! 😂
  14. Mukuro_W

    I'm new to all this. CRT warping/geometry issues: see photos. Easy fix?

    I hope you have already fixed your crt but it is clearly the yoke which is not well centered in place , you have to slightly rotate the yoke without touch the rings. To do this you have to loosen the retainer clip for first then move the yoke, the most important, you need a mirror in front of...
  15. Mukuro_W

    Nanao MS8 buzzing sound

    This is the best dual freq chassis ever made by Nanao, it Is a rare variant of ms8 29 which come with the same rgb amp ic of the ms9, it has the same easy color and withe balance of the ms9 but it is alltheway sharper like any ms8, the noise is just hv leakage most likely from the anode cap...
  16. Mukuro_W

    REPRO SEGA, SNK and TAITO Panels

    He is great, received a vewlix subpanel wich is the best ever made...
  17. Mukuro_W

    Repro / Custom panel for various Japan cabinets ( Sega / SNK / Namco...)

    He is the Magician Lord of the control panels, received 2 x Vewlix F and those are better than the genuine one....
  18. Mukuro_W

    Another Sanwa 29E31 gone

    Check the polyester capacitor on the HOT collector, sometimes those test good but they are not once the power is on. Also check the diodes and resistors in this line.
  19. Mukuro_W

    Jojo HFTF unlock code not working

    Thank you so much! It Is working!
Top