Search results

  1. nem

    CPS1 Multi - Support thread

    Macs add configurations files to all removeable drives, so called dot files. These have caused issues with Darksoft multis in the past. Try removing these files with dot_clean in terminal.
  2. nem

    FS: Dave's Arcade Storage Bin Pulls Updated 05.16.2022

    No, they haven't. The price for one has quadrupled in four years. Before that they were slightly more expensive than Astros, but cheaper than, say, Cutes or Ponys.
  3. nem

    Force feedback - Mario Kart GP vs Mario Kart GP 2

    I bought new ones from Namco. I think they're 5K. I can take a pic in a few days.
  4. nem

    Force feedback - Mario Kart GP vs Mario Kart GP 2

    The parts are the same between the two games, so I don't see why one would be somehow better than the other. I've had a pair of Mario Kart GPs at an arcade for over a year. So far, I haven't had any issues with FF. For my cabs I have Recapped the Triforce motherboards Replaced the PSUs...
  5. nem

    18 Wheeler monitor? Is it 31khz?

    Model 2 outputs high impedance video. I'm not sure if these US cabs have the 15-pin AMP UP connector on the side of the monitor? (I can't see that part from your pic as the frame is in front of it) That connector is normally wired to to the high impedance video input. The pinout for it is here...
  6. nem

    Noob 246 power question.

    Measuring PSUs without a load on them is meaningless. Hook up the systems and adjust +5V close to 5.00 or very slightly over. Take measurements from the system. Once your +5V voltages are in line, power cycle the cabs. What's your +12V now showing? Unless it's way under, it should be fine.
  7. nem

    CPS1 Multi. Official Thread

    Slam Masters
  8. nem

    Taito Type X2 Upgrades and Mods

    The game was released officially in the UK in an upright cabinet with a widescreen LCD. I'm almost sure the aspect ratio was correct and not stretched. The graphics card in the Chase HQ 2 Type X+ is a Radeon 9800 Pro. No custom firmware needed, works with stock. I know because I had to change mine.
  9. nem

    Taito Type X2 Upgrades and Mods

    Try the other dips as well. I'm sure there was a way to have this run in 720p.
  10. nem

    CPS1 Multi. Official Thread

    Yes, but he listed both options. But it's Derick, of course he's going to go for the gold ones.
  11. nem

    Taito Type X2 Upgrades and Mods

    Setting Dipswitch #2 to ON on the X2 should set it to 720p.
  12. nem

    CPS1 Volume Potentiometer Replacement

    Original is 2.2kohm, but 2kohm will do fine. Pin spacing is 5mm x 5mm So for instance this should work
  13. nem

    CPS1 Multi. Official Thread

    Yo, I'll take a pair with my Vewlix Marquee lights.
  14. nem

    MIWA AB2551 Locks (Sega knock offs?)

    No, the Sega keys aren't compatible with this Miwa lock. I have similar Miwa locks on some of my coin box doors.
  15. nem

    Help identifying a coil on Nanao MS9 board

    6.3V will go to pin 4 heater on CN502. 12V will go to pin 1 VCC on LA7837. 24V will go to pin 8 pump up supply voltage on LA7837. Anyway, I suggest you make a thread about this on the ArcadeOtaku forum. There's two guys there that know the MS9 inside out. Best to ask the experts.
  16. nem

    Minigun Supergun - An Open Source Supergun

    If the same switch is used, yes. You can double check with a multimeter.
  17. nem

    Key for Sega NNC Back cover

    The back cover can be harder to open because it has most of the weight of the cover resting on the cam. Try using some pliers for leverage (don't overdo it though if in fact it's a different lock).
  18. nem

    18 Wheeler monitor? Is it 31khz?

    That's a MS2931. It is trisync. I would definitely grab that, even if the tube has burn in (which it likely has).
  19. nem

    Help identifying a coil on Nanao MS9 board

    You have pin 2 on the flyback desoldered, so you're dummy loading b+?
  20. nem

    Capcom Big Blue Q-Sound audio issue

    That's a Sega amp. Same one as in Naomi Universal / Net City.