Search results

  1. ShootTheCore

    Late introduction. Greetings from Iowa

    Welcome! I'm looking forward to 2Dream - new home-brew arcade games are few and far between!
  2. ShootTheCore

    Irem UNDERCOVER COPS Graphic issue [ HELP ]

    Since you have a programmer, try swapping the chips out out with programmed 27C040 or 27C4001 EPROMs anyway. It is rare, but it is possible for a chip to read out on a programmer properly (since the reading is done sequentially) and not operate correctly on the game PCB (since the game reads...
  3. ShootTheCore

    MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

    Aw … thanks @kikaso . :D
  4. ShootTheCore

    MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

    I typo'd on my earlier post about the mister.ini file. The default mister.ini file that is in place with a fresh MiSTer installation sets the resolution to 1280x720 (720p) which most displays support. If you don't get any display from your HDMI port at that resolution then I'd make sure the...
  5. ShootTheCore

    Irem UNDERCOVER COPS Graphic issue [ HELP ]

    Yep, that should work fine. Both chip models have the same pinout.
  6. ShootTheCore

    Irem UNDERCOVER COPS Graphic issue [ HELP ]

    Great minds think alike! :thumbsup:
  7. ShootTheCore

    MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

    The mistercade.ini sets the output resolution to either 15khz (320x240 resolution) or 31khz (640x240) depending on the ini file you use, which isn't compatible with most HDMI displays. The MiSTer architecture doesn't allow for the HDMI to output at a different resolution than what is outputting...
  8. ShootTheCore

    CPS1 Multi - Support thread

    You could purchase and install one of @Mitsurugi-w 's Remote DIP Switch solutions to have fresh new functional DIP switches for your board.
  9. ShootTheCore

    MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

    I believe the Cave games don't like having Coin+Start triggering simultaneously. Try mapping Coin and Start separately and see if that makes a difference.
  10. ShootTheCore

    Irem UNDERCOVER COPS Graphic issue [ HELP ]

    OK, the four ROMs responsible for sprite data are C0, C1, C2 and C3. The components installed into those sockets in your pic are all identical NEC D23C4001EACZ chips, so we can't tell from the labeling if they are each installed in the correct socket. I think it's likely that each chip is in...
  11. ShootTheCore

    Darksoft's MultiMVS Latest Firmware, Menu and Instructions

    Fix your MVS battery and your issues will likely all be cleared up. From the first page of the manual:
  12. ShootTheCore

    CPS1 Multi - Support thread

    If you search archive dot org for "multipacks" then you should find the right files.
  13. ShootTheCore

    CPS1 Multi - Support thread

    The card should be formatted as FAT32. Just extract the zip contents to the SD card - you'll see a "games" folder in the root of the SD card, and all of the game files will be inside of that.
  14. ShootTheCore

    Irem M92 Multi Game Support

    Yes, a Major Title 2 donor should work fine.
  15. ShootTheCore

    CPS1 Multi - Support thread

    The traces were cut before to get the C Board to work without a battery, and the solder was later added to reverse the mod so that it would work correctly with the Multi. If you have a multimeter, check that all three of the soldered pins are reading continuity to Ground - you can see that the...
  16. ShootTheCore

    General talk about CPS1.5 Multi Addons

    Got my Multi all kitted out today with the 3P4P add-on, filter PCB mounted DIP switches, Spinner add-on, color-correct RCA audio ports and a prototype 10mhz / 12mhz clock mod. Everything is working great! :thumbsup:
  17. ShootTheCore

    Fantasy Zone 1 on System 16B

    I have it for the System 16B Multi, but not for a stand-alone ROM board.
  18. ShootTheCore

    Fantasy Zone 1 on System 16B

    That’s Fantasy Zone 2 that runs in 16C. The original Fantasy Zone runs on the System 16B fine with the right ROMs.
  19. ShootTheCore

    Irem UNDERCOVER COPS Graphic issue [ HELP ]

    Can you post a closeup picture of this section so we can read the labels?
Top