Search results

  1. Kujako

    Atomiswave SD Clean Up + Toshiba PF

    Love it, always jealous of folks who have these cabinets.
  2. Kujako

    New dumb idea: building a Neo Print system

    While I can curse in several languages, french isn't my strong suit (title says it has english subs, but they're not working for me). Big thing I noticed when I previously viewed this video is that when he boots up, it's not mirrored like what I'm seeing and it goes straight into the attract...
  3. Kujako

    New dumb idea: building a Neo Print system

    Don't suppose anyone knows the hardware dip to get into the test? Pulling the 7th from the right pin low isn't doing anything.
  4. Kujako

    New dumb idea: building a Neo Print system

    So after building a very high tech control panel, it's still on the "Call the person in charge" screen when pressing the buttons in alternating order multiple times. Fair chance I've messed up something, but if OK and CANCEL are adjacent to GROUND (and I confirmed the right most pin is ground)...
  5. Kujako

    Cheap third party chassis option for WG 25" with CGM-2500?

    Had to very slightly file down the inside of the adapter, the rotary switch seems like its a weird size (possibly imperial rather than metric). But overall it's a good fit. Will test voltages this weekend.
  6. Kujako

    New dumb idea: building a Neo Print system

    Will try that, worse case I can just short all the input pins to ground if I'm not sure which pin is which. Edit: the wiki has the controller pinout. CTRL: From the 6th pin: LEFT, RIGHT, OK, CANCEL, GND. Active low.
  7. Kujako

    New dumb idea: building a Neo Print system

    So looks like the "Call the person in charge" message is common, even showing up in Mame. Still looking into how to proceed. Found a manual in Japan, working on acquiring it.
  8. Kujako

    Cheap third party chassis option for WG 25" with CGM-2500?

    I can, but it takes a lot of effort. I confirmed it powers on, but will want a knob before I do much more. Also want to hit everything with contact cleaner. The ones you list have a tension screw or are thin plastic. I've ordered some of these which should be a better fit...
  9. Kujako

    Cheap third party chassis option for WG 25" with CGM-2500?

    Did finally get it apart for a visual inspection. Zero signs of any issues despite the age, even the casing is still bright and shiny. Will test that the voltages are correct, but thinking this can go a bit before capacitors and resistors are replaced. Far as I can tell, this unit was close to...
  10. Kujako

    Cheap third party chassis option for WG 25" with CGM-2500?

    I didn't think so, but looks like you're right. It's very stiff, and the knob is broken somehow so that it's slipping. Physically it seems OK, but the metal ring is able to rotate in the plastic housing. So now I need to figure out a replacement knob. I think it's a 6mm D shaft knob. But may...
  11. Kujako

    Cheap third party chassis option for WG 25" with CGM-2500?

    So lamentably, I'm not getting any signs of life from the 467 unit after cleaning it and the main potentiometer control feels very spongy and doesn't click into place as I would expect. Always a chance I'm doing something wrong, but I fear it's headed to the repair project pile. Anyone have any...
  12. Kujako

    New dumb idea: building a Neo Print system

    I'll give that a try, as well as pulling the audio jack connector for the printer to low. The DIN8 connector is output only as I understand it, but there is a "ready" state signal the printer sends over the 3.5mm audio connector. The single slot board I'm testing with has that connector torn...
  13. Kujako

    New dumb idea: building a Neo Print system

    Well, this is something... unfortunately I think I'm the "person in charge", and I don't know what to do next. It may be that it's looking for the printer. Booting without a cart shows the MVS style color quilt pattern, so no default service mode. With the cart it flashes a couple messages, then...
  14. Kujako

    New dumb idea: building a Neo Print system

    Ah... that makes a ton of sense. Have to avoid flickering etc. Will try tonight or this weekend with the camera wired up.
  15. Kujako

    New dumb idea: building a Neo Print system

    The RGBS is labeled as output and my assumption was that it's for the main display (the harness cable I have is clearly for a standard 15khz CRT). But that could be totally wrong. Will try the s-video output (three of the four s-video ports are inputs).
  16. Kujako

    New dumb idea: building a Neo Print system

    Still searching for a service manual... no progress yet, moving the search to Japan.
  17. Kujako

    Cheap third party chassis option for WG 25" with CGM-2500?

    Yup, but eyeing some cheaper options I'll want to exhaust first.
  18. Kujako

    Cheap third party chassis option for WG 25" with CGM-2500?

    Have the 467 in hand, pile of adapters but no CR-23. Ah well... had to take a shop vac to it to clean out all the disintegrating foam. Will test it out and assuming it all looks OK will then source a CR23.
  19. Kujako

    New dumb idea: building a Neo Print system

    So wired power and RGBS and neither unit I have showed any signs of life. So either both of them are bad in the exact same way, or I'm missing something. May have to dust off the oscilloscope to check the RGBS output. Based on the wiring I have I'm operating under the assumption that right to...
  20. Kujako

    New dumb idea: building a Neo Print system

    Yup, don't have any of the red label ones as of yet but figured I'd get the dual slot board running first.
Back
Top