Search results

Hi, Long time, I'm finally starting to clear space for a permanent arcade fixture, so time to resurface 😂. OK, so I just had a thought. 2P cocktail with any 2P game, lets just use Street Fighter as an example. So a CPS2, all the adapters, DExx-vd_isl and a widescreen monitor. Would it be...

Trawling through my memory banks... I remember I had similar problems with soldering my board, I suspected a cold joint and putting a bit of hot air on it fixed it. I used a cheap Hot Air Desoldering SMD Rework Station but you could probably get away with a heat gun with a small nozzle and a...

Fully aware that Frank hasn't been here in years (can't thank Frank enough for all he's done) but I have a couple of these and I want a compatible mini DIN to VGA cable, what do folks use, from memory it's "Saturn" inspired?

Interesting comment on the SD card holder in the Sparkfun page:

@Darksoft thanks, you're spot on, it's the socket, I'm guessing it's a cold solder joint, I've managed to get the multi working today, my guess is the hot air improved things and wiggling got it working. I think this is it https://www.sparkfun.com/products/127 dang it's surface-mount, I...

Thanks, not sure about the "existing" SD, there are some erroneous hidden Mac files on there though, this SD reads fine in Windows and it was working fine before I put the multi into the cupboard. The new SD, I formatted and moved the test files to that using Windows.

Thanks, I've used compressed air on it and also I surrounded the SD card socket in kapton tape and used my hot air rework box to heat up the socket just in case there was a cold solder joint on there, nothing has worked. It was stored indoors, in the protective case, in a cupboard. The CPS...

Thanks, tried all that. I got a brand new 16GB formatted to FAT32 with and SD Formatter tool from the SD card association, is that the one, I copied over the test folders from here https://www.arcade-projects.com/threads/romset-to-verify-your-cps2-kit.11886/#post-191917 to see if that worked...

Bad sdcard?

Hi, System was working fine, it's been in a cupboard for 6 months, took it out today, powered on to just "LCD init" on the display and no video. I bought this with the mod already performed. The CPS fan is going. The battery was removed at some point in the past. I've tried IPA to clean it...

I used @Frank_fjs DIN to SCART PCB and an off the shelf DIN cable, works great.

@klee123, @evilsim is da man!

It depends on your knowledge level but a logic probe is a pretty cheap and easy to use troubleshooting tool: https://www.amazon.com.au/Elenco-LP900-625-Logic-Pulser/dp/B0002E7X5O You basically connect it to your PSU 5v and when you touch a pin or PCB contact you can hear the logic, or the audio.

@klee123 all good, did you get it from ebay or someone on here? I had no audio on the minigun because I decided to leave out the audio jack, the audio jack has a switch in it so even if you don't use the jack you need it to get audio out of the DIN. If you bought yours assembled then it's not...

@klee123 did you solder the minigun yourself?

Gotcha, CPS2 definitely doesn't need -5v and Denjin Makai II looks like it doesn't need it either, all my old Konami boards need it.

What arcade board are you using, some of them need -5v (minus 5v) also?

Yes, the DIN connector on the minigun carries sound.

Thanks @xodaraP, is there an easy way to test the gnd loop on a VSHG, continuity between point A & B but where is A & B?

Thanks @xodaraP I have continuity pcb - usb --------------- 1 red - [+] 2 wht - [D-] 3 grn - [D+] 4 blk - [shield] 5 blk - [shield] Now pin 4 on the USB [-] is not connected but I was thinking that that doesn't matter if the PCB is getting negative (PCB pin 4) from the shield wire? The white...