Search results

Yup thats me, I found a SvG discord and asked around about the versions. Apperently V100JP (which is what I have now) is an older version. The community prefers V200 and considers it completely different. The balance and mechanics are different enough that they won't play V100. So if you're...

Could I get the STL file for this as well? I need to swap my monitor!

Anyone got any suggestions for a good dolly I could use to transport candy cabs up and down stairs? I'm willing to spend decent money if one kicks that much ass...

So it's just a socket chip replacement? Can anyone burn me a new chip?

Is this possible? Are the games hard coded for certain regions or can a bios be swapped?

FIGURED IT OUT! The HOTD3 setup has a connection for a .5A fuse on the 12VDC rain to the guns. I didn't have that connected so my guns weren't firing! That is most likely your problem, if you still have it, you can connect the red/white and red/black wiring together and it should be fine!

I will double check but I was able to make the trigger enable when I jumped the trigger to common wires for both players using the 9pin JST XH connector. According to both manuals, the pinouts are the same, minus the reload switch. However since we are running into the same issues, I'll tear...

I bought a hotd3 wiring setup and it's connected to a Type 1 JVS io and I've tried 3 different ones. The trigger input and out of range do work when jumpered with the connectors so those should work. I can get pics of those as well if you'd like.

Attached should be all the photos of the custom wiring to the IT board. I haven't checked the continuity from the gun to the IR board but it's factory wiring from the AMP connector to the gun inputs.

NOTE: I do not need the protection board, I already got one. Its just included in the picture since that was the best picture of the board I could find!

Looking for a working Sega Naomi IR Gun Board for my setup that is Rev 4 or Higher. I need to work with just Naomi games, I don't plan to use it for anything beyond that. Please message me if you have one for sale.

Will do Tonight, I also forgot to mention I had did a multimeter check from the sensor in the gun to the jst connector and all 7 wires were good. I have the gun protection board and the LEDs on it are on. I bought the 2 gun boards without confirmation they worked but that may be where the issue...

Do I need both guns hooked up? Also I cannot get the trigger to activate from shorting pins 1 and 2 for 7 pin connector for the gun. I can get trigger to show when shorting the cables going directly to the jvs io. Is there a way to test the gun sense board? I think that may be my issue...

I This isn't my gun but this is the setup I have. I should have the IR Type 2 guns (9-Pin JST XH 838-14144 / JPT-2030 / OMJ-GZH200D) I'll post close ups of my wiring since I had to redo some of it to adapt these guns to connect properly to the HOTD3 setup (AMP to MOLEX)

Hello, I am trying to assemble parts for a Lightgun setup and I believe I have everything. I am however getting nothing when I try to calibrate the guns. I believe I have the wiring correct and I can see the IR sensors on when I take a picture with my phone. I am trying to do HOTD2 through...

I got 2 jvs IO hooked up in sequence but I only get controls for 1/2 player off the 2nd IO. Is this something that these boards support?

I got a Raiden 2 USA board that looks like it has some graphical issues. I did see any issues with pins on the board but I didn't break out a microscope to see. Maybe one of the graphics chips needs to be replaced?

Does this exist? Is there a way this is compatible with the Dark soft Multi by chance?

I believe the router handles it all via DHCP but its gotta be some special network that runs between cabinets via the router.

Prob gotta have the router?