It's been a Year an a half but I found a company to make the sub-harnesses for me and these are back in stock!
- Thread starter twistedsymphony
- Start date
Tele-Viper
Beginner
For MK1 and MK2?
Do I get them jsut by rodering the kits? I may have to do that.
Yes, link in the first post.
XtraSmiley
Legendary
Hey, bumping this up, do you still make these?
KalessinDB
Grand Master
If he doesn't, I accidentally bought an extra MK1 kit that I could pass along. But I don't want to step on any toes.
you bought it, you own it, no reason you can't resell it if you'd like to.
ChuChu Flamingo
Enthusiast
You ever plan on making these again? I need one for nba jam.
I'm not doing 3D printing anymore as my job takes up too much of my time.
the 3D printed parts are available on thingiverse though if you'd like to print your own.
the 3D printed parts are available on thingiverse though if you'd like to print your own.
ChuChu Flamingo
Enthusiast
MK1 will work for NBA jam right?
is it a T-Unit MK1 or a Y-Unit MK1
T-Unit MK1 is the same as NBA Jam
Y-Unit MK1 is different.
MajorHavoc
New User
Thanks to twistedsymphony for making these and making the 3D models available.
I have a Y-unit with CVSD audio board and want to build my own mounting. I read the thread and looked at the pictures but still can’t figure out how many of each item to print. I guess I could just print some of each and try it.
Do the instructions show the items in a kit? If so, can someone post them?
Do I need:
1 x volume pot
1 x offset standoff
2 x standoff
4 x screw with nut
Thanks
I have a Y-unit with CVSD audio board and want to build my own mounting. I read the thread and looked at the pictures but still can’t figure out how many of each item to print. I guess I could just print some of each and try it.
Do the instructions show the items in a kit? If so, can someone post them?
Do I need:
1 x volume pot
1 x offset standoff
2 x standoff
4 x screw with nut
Thanks
MK2 (8MB ROM version)
- 4x 18mm standoffs
- 4x M3x24mm screws
- 4x M3 acorn nuts
-------------
T-Unit (Except MK2)
- 1x T-Unit Volume Pot Standoff
- 3x 18mm standoffs
- 4x M3x24mm screws
- 4x M3 acorn nuts
- 1x 50K ohm volume pot
--------------
MK1 Y-Unit & Total Carnage
- 1x Y-Unit Volume Pot Support B version
- 2x 18mm standoffs
- 2x M3x24mm screws
- 3x M3x8mm screws
- 3x M3 acorn nuts
- 1x 50K ohm volume pot
--------------
Y-Unit (Except MK1, TC, & T2)
- 1x Y-Unit Volume Pot Support A version
- 3x 18mm standoffs
- 3x M3x24mm screws
- 1x M3x8mm screws
- 3x M3 acorn nuts
- 1x 50K ohm volume pot
- 4x 18mm standoffs
- 4x M3x24mm screws
- 4x M3 acorn nuts
-------------
T-Unit (Except MK2)
- 1x T-Unit Volume Pot Standoff
- 3x 18mm standoffs
- 4x M3x24mm screws
- 4x M3 acorn nuts
- 1x 50K ohm volume pot
--------------
MK1 Y-Unit & Total Carnage
- 1x Y-Unit Volume Pot Support B version
- 2x 18mm standoffs
- 2x M3x24mm screws
- 3x M3x8mm screws
- 3x M3 acorn nuts
- 1x 50K ohm volume pot
--------------
Y-Unit (Except MK1, TC, & T2)
- 1x Y-Unit Volume Pot Support A version
- 3x 18mm standoffs
- 3x M3x24mm screws
- 1x M3x8mm screws
- 3x M3 acorn nuts
- 1x 50K ohm volume pot
MajorHavoc
New User
All my pots are too big to fit into the 3D prints. Does this one from Digikey work?
P160KNP-0QD20B50K
https://www.digikey.com/en/products...IgTCBcDaIAoEYBsAGA0gOTgWhQRQBEwUAhAVnRAF0BfIA
P160KNP-0QD20B50K
https://www.digikey.com/en/products...IgTCBcDaIAoEYBsAGA0gOTgWhQRQBEwUAhAVnRAF0BfIA
yes thats the exact model I use
