Recent content by PaulWoodpross3r

Bump, I think you ended up keeping them as Daytona 2 though. If I remember correctly I sold you a DSB2 sound board on eBay back in 2021 or 22. As much as I love Sega Super GT and Daytona 2, It is definitely possible to run OutRun 2 and SP on Chihiro system in these but it will require some...

Update: I have the Chihiro system (mostly) working except the settings revert to default settings every cycle. I've read it's due to a bad dimm battery on this specific software and not on regular OutRun 2. - Currently have the Chihiro downscaled to 15khz through GBS-C. - I was able to hook up...

Hi, I found another Outrun2SP Chihiro set that runs off a CF Card instead of the GD-ROM drive. I want to wire it up in my Le Mans 24 cabinet which has the Model 3 dash. No, I'm not "converting" the cab as I plan to put the Model 3 cage back in, but I want to rotate games. I dug up the...

I can confirm these fit a Nanao MS9 frame. I got the brackets 3D printed using prototyping PLA filament, and while a couple of the mounting holes were not perfectly printed, the Unico still mounted in there nice and snug using the 8 M4 bolts with washers and nuts. Here is the ULM26 installed...

Dude, this is remarkable work! I can see where this can benefit other cabinets that use the Nanao MS8 and MS9 tubes, like the Japanese Daytona USA cabinets. I'm going to try to 3D print these myself to use on my Harley Davidson (MS9) that needs a cap kit. On your design, do you just slide the...

Thanks. I was going to use the plywood strips for those mounts as plan B. The monitor mounts are these, right? (Where my finger is pointing). I know the whole thing is removed with them. Theoretically I would need to use a longer bolt to accommodate the extra half-inch from the plywood strips...

Hi, I picked up a Harley Davidson game almost 2 weeks ago that I have been loving and restoring. I have already replaced the rosta suspension unit which was worn and made the handlebars lean to the right, and I replaced the start button which had a dead bulb. The Nanao needs to be recapped but...

Yeah, I was going to bring my N2/cart and meter along to check if the PSU voltages ok. It's a little easier to do with a Naomi than Model 2/3. I do have a VGA cable without pin 9 too as I know the ground line likes to explode on Naomi filter boards when connecting a full VGA cable to certain CRTs.

Decided on setting up additional boards in this cabinet by putting them on a loose, adjustable 1-tier shelf, instead of mounting them to the sidewalls. I would rather not run the risk of protruding and ruining the art in this cabinet by drilling holes, as this cab looks to be in very good...

Edit: I ended up not getting this cabinet because it was too deep for my floor space, so I got a Harley Davidson L.A. Riders 29" sit down instead. Next month I will be picking up a Wild Riders. This is not the Naomi Universal cabinet (which I'll admit is way nicer), but the US sit down cabinet...

Update: I can confirm J6 is what handles audio signals. Pitch is indeed 2.54mm as I soldered on 4 Dupont male headers to a 4-pin Dupont female header. This plugs to my Sega Model 2A through 3 audio harness. If you don't have the TE connectors to crimp, you can also plug Dupont connectors into...

Hi, I'm picking up my first non-Sega arcade system from a guy, a Time Crisis 2 Namco System 23 set with metal box. I've had a look at the TC2 manual and it seems to me that CH1 and CH2 (marked in the wiring diagram picture) represent the audio signals for the system. Is that for connector J6...

Yeah I heard about dual gang pots. There is that rare case though where a replacement pot for a controller is next to impossible to replace, let alone a dual-gang variant for it. I've also found this thread where somebody Frankenstein'd a pot with a chip to output two signals; perhaps I could...

Hi, This is semi-related because a project like this would be handy for certain home controllers of mine. Has anyone attempted to wire 2 analog inputs to a single potentiometer in an arcade-related project? I've stumbled upon similar projects like this crossfade circuit here that appears to be...

Hello, Does anyone have a spare shifter for Initial D 7 AAX or Stage 8 available they would be willing to sell for me working? I am planning to swap out the shifter in my Le Mans 24 (Model 3 FFB) cabinet with this one, as I think this shifter is ridiculously comfortable having played the...