BOUNTY for Taito G-Net CF Conversions.

Would it be possible to prompt it to put the music volume just below the sfx volume?
Or tell it to compare to og?
Might fix the recording volume issue.
This is unfortunately more complex than it would seem on the surface, but I will dive into this further and figure out the best solution for a better balance.

Hi! That was my feedback from testing the Rival Schools (ZN1) conversion on the Taito G-NET system.
Sorry for the confusion, I knew yours was about Rival Schools, I'll look at that as well as the pending DOA++ issues posted earlier :) and I'll get Japanese Rival Schools going.
 
Hi! :)

I will need to do a conversion of Gallop Racer 2 Link HW if I want to test the link mode.;)


1794710352459.png
 
Okay, thanks for the bumps to the thread to get me to come back to this. I started working on the final 8 likely conversions a few months ago, and I finally got back to it, finished them out, and tested them on my G-Net hardware tonight.

Conversions completed:
  • 1 on 1 Government (TPS BIOS)
  • Dead Or Alive ++ (TPS BIOS)
  • Gallop Racer 2 (TPS BIOS)
  • Gallop Racer 3 (TPS BIOS)
  • Logic Pro Adventure (TPS BIOS)
  • Monster Farm Jump (TPS BIOS)
  • Tecmo World Cup Millennium (TPS BIOS)
  • Tondemo Crisis (TPS BIOS)
https://drive.google.com/drive/folders/1NLAoPO-s4LCNvB4XO5yoHFswxy-t1erN?usp=drive_link

Both .img and .chd files at the link. You can use the .chd files like the other ones with the G-Net Flashing Software from ikotsu, or you can just flash the .img files using Win32DiskImager or your preferred program. The same CF rules apply as the other conversions; make sure you are using working cards, Sandisk 64MB-2GB. I tried an 8GB card and it wouldn't work, but my 64MB ones are just fine. Please let me know if you run into any issues, I tested each game on a fresh flash but obviously I can't play each for hours before releasing.

I understand that some of those pledges were from a very long time ago and that times and circumstances change. If you are still willing to pay out the pledges I really appreciate it, but understood if it is not possible and absolutely no hard feelings. EDITING TO MAKE IT COMPLETELY CLEAR THAT I AM NOT EXPECTING OR HOPING FOR BOUNTIES FROM ANYONE, ANYTHING IS APPRECIATED BUT THERE ARE ZERO EXPECTATIONS. CONSIDER THE @ 's BELOW AS A HEADS UP THAT THE PROJECTS HAVE BEEN COMPLETED AND THAT YOU SHOULD PLAY THESE COOL GAMES. Mostly, I just want people to enjoy these games (especially Logic Pro Adventure and Tondemo Crisis, what gems).

@twistedsymphony @rewrite @Darksoft @ekorz @jugu @suverman @Brentradio @theoddtech @CoinFeeder @ShootTheCore @Tietscha @9999 Damage

Bounties can be sent to [email protected] via PayPal with no expectations, truly appreciate y'all and hope you enjoy the games.

Also, if there is an appetite for further conversions please let me know what you are interested in. I was considering doing research on porting Brave Blade's music from the Yamaha chip to the native chip to see if it is even possible to get music going directly on the G-Net, could be fun.

Lastly, someone needs to get on making new stickers for the CF cards :D
I tested Logic Pro Adventure, Dead or Alive++, and Monster Farm Jump, and they all work perfectly. This is fantastic! 👍

If possible, I would appreciate it if you could add the Japanese version of Rival Schools.
 
Last edited:
Time to work on PR2 now, Hammy sent me RAMs weeks ago. i already improved disk loaders. All SPU read hooks need to be reinvestigated
Game will probably run only with Sandisk 30MB/s card like these:
1794762224732.png

All GNET games setup cards very slow - if you ever get performance problems with the cards - i already got the tweak and near 8MB/s in PR2 Testmode

io16: lui t0, $1fb7 ; 16 bit IO
sb zero, 0(t0)
lw t0, _IO16_2 ; 16 bit
lui at, $1f80
sw t0, $100c(at)
ori at, zero, 16
io16w:
bne at, zero, io16w
addiu at, at, -1
jr ra
nop

align 4
_IO8_2 dw $20152E66 ; extmem 8 bit
_IO16_2 dw $20151E66 ; extmem 16 bit

The last 66 nibbles here are important for CF speed. Sandisk 8MB/s can go down to 33 here without load issues. This maybe only relevant for PR2 for FMV and pre-stage loading

As a Tip: Also loading in 16bit mode from CF could improve your load speeds - "If it may be relevant" - Brave Blade runs FINE!!! YEAH
 
Last edited:
Current state:

All 8 "likely" games are converted and working
-DOA++ has a known bug with slight slowness in some loading, and some jank when scores are calculated at the end of a match. Gameplay is fine. Actively researching @ekorz
-All other 7 games have no currently known issues

The first of a group of Yamaha sound games has been converted
-Brave Blade, no known issues
-Next game not decided, maybe Bloody Roar 2

The first of a group of Q-Sound games have been converted
-Rival Schools; reported issues of a failed rom check and music continuing to play during the service menu have been fixed but not released because I found a post-round flickering problem, even in the current build. Actively researching
-Audio imbalance and potential voice delay has been reported during the attract cutscene; I played through this and didn't see any issues that were incredibly obvious, so I'll be comparing to PCB to try to analyze and fix. Not started yet
-An issue was reported that the G-Net rebooted after the full attract screen flipped. I haven't made any changes here as I wasn't able to reproduce this on G-Net hardware nor in simulation. @chacal231077
-I will be switching to the Japanese version from the next release due to multiple requests and will stop publishing the US version until all known issues are fixed; actively troubleshooting issues on two builds is not fun :)
-All of the work put into Rival Schools and your feedback will hopefully make further games considerably smoother

I have begun architecture on an English version of Tondemo Crisis by extracting assets from the English Playstation version; a similar but simpler process to how I add music to the Yamaha and Q-Sound games. @ekorz
 
Last edited:
Updated the structure of the drive to separate out Yamaha and Q-Sound games since they are currently more experimental

Uploaded the Japanese version of Rival Schools to the Q-Sound folder
-Fixed an issue where music would keep playing if you went into the service menu
-Fixed an issue where the rom check would fail and freeze the game
-Fixed an issue where character sprites would flicker at the end of a match
-Initial Japanese release
-Removed US release for now
 
I've always used Raspberry Pi Imager on Ubuntu for Taito G-NET game RAW and .image files,
and I've never had any issues :thumbup: , unlike with GNETFlasher.exe:unsure:

1794766567543.png

1794766608779.png

1794766646045.png
 
GNETflasher uses chdman in background process ... i just wanted an easy solution to flash your new chds :) .. finishing beer here and trying another game one now!

cheers
 
New version of DOA++ uploaded, fixes the weird jank during scoring. Loading times relatively unchanged (slightly longer than original PCB), this may be out of my hands and doesn't effect the game so I'm calling this finished for now unless anyone finds any further issues!

On to Strider 2.
 
Maybe it's a difficult idea, but with the growing number of compatible games for the G-NET, I've recently been wondering whether it would be possible to develop a system similar to the NetDIMM/Netboot setup used on the Sega Naomi, allowing us to avoid collecting dozens of CompactFlash cards.

Here's the idea:

A Raspberry Pi Pico 2 W, possibly combined with additional hardware to handle the GPIO requirements, could provide a microSD card interface, a CompactFlash interface, and wireless connectivity (Wi-Fi and Bluetooth).

The Pico would host a local web server, allowing the user to connect from a phone or computer and select a game through a browser, just like with a typical netboot system.

Once a game is selected, the Pico would read its image from the microSD card and emulate a real CompactFlash card, responding to the signals from the G-NET through the existing PCMCIA-to-CompactFlash adapter.

Another interesting aspect is the Pico's small form factor: the entire custom PCB could potentially be designed to fit inside the existing PCMCIA-to-CompactFlash adapter, or at least within its available space.
 
Back
Top