CAVE PGM Conversion Labels - IGS PolyGame Master

[GoenitzNYC]

I've been working on a set of Cave labels too. I could post them here if that's cool?

By all means post! That's why I created this thread, for all to contribute and enjoy!

 

[Neo-Alec]

I ended up just trimming my sheep_nova labels and resticking them with 3M spray glue. They aren't perfect but they look a lot more like real PGM games on the shelf.

 

[nio]

I need laböes foe the chips, like the one in the build thread. how do you make them?

 

[Fluffy]

I need laböes foe the chips, like the one in the build thread. how do you make them?

I am using Avery labels, 46x11.1mm, https://www.amazon.co.uk/Avery-L7656-25-White-printer-label/dp/B001ARZNK4/ref=asc_df_B001ARZNK4/

They've got an online designer, though I found that the bleed area I added got trimmed to the exact outline of a label, so prints can have thin white edges. Otherwise they are slightly trimmed versions of the full size labels someone posted here already.
The numbers were added with the csv import feature in the label maker.

 

[nio]

Cool thanks!

Can you share your design?

 

[Fluffy]

I don't have the source artwork any more, but if you have the logo it should be literally minutes to set up in the online label designer.
I've got these PDF printouts, but as I mentioned before it would be better if each label was slightly bigger than the cutout on the sheet, so alignment errors don't show up as white border. I just printed the first page, which was more I needed.

 

[flo_oh_oh]

Hi guys, i'm looking for a DDP II bee Storm label, someone have it ? Thanks

Here's a quick cleaned up pic of my label, give you something to start from if someone hasn't recreated it.

Thanks !!!!!

 

[SmokeMonster]

Here are the final versions of my remastered labels. PSD template here.


Print at 600DPI (17.81cm wide). The sheet is 7x4 inches.

 

[Ravepants]

nice one smokemonster, they look amazing!

 

[Derick2k]

Gonna get these professionally printed/cut, thanks brother.

 

[-Ace-]

Nice work, thanks!

 

[SmokeMonster]

Gonna get these professionally printed/cut, thanks brother.

Could you print me off a spare set?

 

[Derick2k]

Gonna get these professionally printed/cut, thanks brother.

Could you print me off a spare set?

sure can, ill let you know once I have them.

 

[SmokeMonster]

Thanks!! I updated that post last night with a PSD that is the exact size, and a new PNG. Definitely print either of those and not the first one I posted.

 

[Derick2k]

Thanks!! I updated that post last night with a PSD that is the exact size, and a new PNG. Definitely print either of those and not the first one I posted.

Thanks, did you leave enough extra for bleed over?

 

[SmokeMonster]

I just built them over the original labels I was remixing, so no bleed I think. Hopefully that doesn't screw them up.

 

[Derick2k]

nah, should be fine, I will test them out, thanks.

These will go great with some carts I have been meaning to get done.

 

[RandomRetro]

@Derick2k do you print them yourself or have a good source for label printing?

 

[Derick2k]

@Derick2k do you print them yourself or have a good source for label printing?

Both, I usually test print at home with an LX900, but for the pro stuff I send it out. Specially stuff like the domed badges, or high quality labels with UV protection, die cut etc... A home setup for that would cost too much.

 

[RandomRetro]

Makes sense. I was looking at some holographic film to put on custom labels a whole back but need a better printer to start. Future project maybe.