What's new
By:

FS IC: Sega Swing & Taito Egret 29 Marquee repros

For Sale
Appreciate ya. No rush on the PM response for those other things- but for what it's worth we're all in the same area so it might make sense for you shipping wise.

Thanks sir
 
Small update, finally got all acrylic cut with proper measurements, etc..
Next the artwork. Hard to find someone that cad do screen printing properly over here, but Im looking. If not, might have to go with a digital print, which I dont want.

2020-10-30_19-14-46.jpg


That green acrylic killed my budget on this, and the proper chamfer cut didnt help.

Also, did some repro Vewlix marquees with what i hope is the proper light diffusing acrylic. Will do some side by side comparisons.
 

Attachments

  • 2020-10-30_19-15-06.jpg
    2020-10-30_19-15-06.jpg
    31 KB · Views: 168
jermz1 said:
are you going to be selling the vewlix repo marquee?
Click to expand...
i will sell the extras for now, i ordered a dozen and 6 are spoken for, so 6 left. If there is interest I can do another run as needed.

I need to take some comparison shots though. So I have the taito originals, the replacement with the what I think its the proper light diffusing effect and regular cast acrylic.
 
Last edited:
Derick2k said:
Small update, finally got all acrylic cut with proper measurements, etc..
Next the artwork. Hard to find someone that cad do screen printing properly over here, but Im looking. If not, might have to go with a digital print, which I dont want.

2020-10-30_19-14-46.jpg


That green acrylic killed my budget on this, and the proper chamfer cut didnt help.

Also, did some repro Vewlix marquees with what i hope is the proper light diffusing acrylic. Will do some side by side comparisons.
Click to expand...
there's a nice screen printing place in SF near us that did the Aero Table glass. Would you like their contact information?
 
Battlesmurf said:
Derick2k said:
Small update, finally got all acrylic cut with proper measurements, etc..
Next the artwork. Hard to find someone that cad do screen printing properly over here, but Im looking. If not, might have to go with a digital print, which I dont want.

2020-10-30_19-14-46.jpg


That green acrylic killed my budget on this, and the proper chamfer cut didnt help.

Also, did some repro Vewlix marquees with what i hope is the proper light diffusing acrylic. Will do some side by side comparisons.
Click to expand...
there's a nice screen printing place in SF near us that did the Aero Table glass. Would you like their contact information?
Click to expand...
For sure, I have reached out to a few places here and have some appointments, but it doesnt hurt to get extra quotes. I have all the cut acrylic ready to go :) so if they work out I will send all your way.
 
Derick2k said:
jermz1 said:
are you going to be selling the vewlix repo marquee?
Click to expand...
i will sell the extras for now, i ordered a dozen and 6 are spoken for, so 6 left. If there is interest I can do another run as needed.
I need to take some comparison shots though. So I have the taito originals, the replacement with the what I think its the proper light diffusing effect and regular cast acrylic.
Click to expand...
pmd you
 
Acrylics are made/cut and ready to get the artwork installed. Unfortunately, getting the artwork rescanned. I lost my drive with the art one it, and I was only able to recover part of it. Will find out tomorrow if they are able scan and redo graphics. If not I will have to go back out to the original place I went to which is about couple hours drive each way. Regardless, I will forward all to Battlesmurph to finish these up. I already lost a ton of $$ on this getting acrylics made/cut, plus scanning art, etc.. So, I will let him finish this up, just want to get people to finally get these and I hope they are happy with them.
 
I'll take the torch and make sure you get squared away proper and the job finished up. I have the Swing surrounds waiting and a couple people holding fast for the toppers.

We'll make it work.
 
I did mention to Derick a while ago so I'll mention it to you. I found exact replacement hardware for the E29 Marquees this is the polished truss head screws and matching Acorn nuts that hold the front and back glass together and mount it to the bracket on the bottom.

I have enough on hand to do a few marquee sets, or if more than that is needed I'm sure I can dig up the specs/where I bought 'em.
 
Still watching progress and very happy to have all of you <3

I have 2 Swings to restore now, so I'm in for 2 sets of header and panel :)
 
twistedsymphony said:
I did mention to Derick a while ago so I'll mention it to you. I found exact replacement hardware for the E29 Marquees this is the polished truss head screws and matching Acorn nuts that hold the front and back glass together and mount it to the bracket on the bottom.

I have enough on hand to do a few marquee sets, or if more than that is needed I'm sure I can dig up the specs/where I bought 'em.
Click to expand...
I'd love to get ahold of that information.

I have the plastics in hand. They're cut. I'm sourcing screws now. The Swing stuff is being looked at. The Egret 29 stuff has been scanned, but I'll likely need someone willing to look at the scans and prep them for my screen printer. If anybody knows a guy that'll do it, I'm interested in having those talks to get these finished up. Screen printers are waiting on me.
 
You must log in or register to reply here.
Back
Top