FS (Withdrawn, shipping too high) Supergun Minigun 9-pin full setup including power, controller, cables, custom shells etc (new)

[hatmoose]

Hi Everyone

Supergun Minigun 9-pin full setup including power, controller, cables etc, new - for sale $US550 too expensive to ship.

This is a “full setup” for JAMMA. Hand made by me never used except for testing. Video of testing provided before I seal the box and send it off.
All components/parts/pins/shells are 100% authentic and original from reputable suppliers (Digikey, Mouser, RS) unless otherwise noted.
All the cases are designed and printed by me, these are all custom, you can’t buy them anywhere else - lots of cool little features to find.

1 x Minigun Supergun 9-pin in custom 3D printed case
1 x Meanwell RT85a power supply in custom 3D printed case
1 x Custom power cable (approx 90cm 3ft)
1 x 4-player adapter in custom 3D printed case
1 x Custom CPS1 6-button kick cable (suitable length for CPS1)
1 x Custom CPS2/3 6-button kick cable (suitable length for CPS2/CPS3
1 x PGM 4-player cable (this is an old floppy disk drive cable, suitable length for PGM)
1 x 6 button controller with DB15 plug (you will not win any tournaments with this controller, for testing only)
1 x 9-pin to SCART cable (adequate quality, for testing only)
1 x SCART to BNC converter for RGBS in custom 3D printed case



If you have a PVM with RGBS inputs, or a CRT with SCART inputs this should be a full solution, you will need to bring your own BNC cables and RCA audio cables
If you have a modern TV you’ll need a Retrotink 2xSCART or similar to convert the SCART to HDMI and a suitable HDMI cable

$US550 shipped - packed and ready to ship. I will test and send video before closing the box. Shipping is from New Zealand (Middle Earth!) it is tracked and you can expect it to take 1-2 weeks.


Paypal F&F
My feedback is here https://www.arcade-projects.com/threads/positive-feedback-for-hatmoose.20760/#post-319079
If your feedback is positive and more than mine you can pay nothing now - pay when it arrives and you are 100% happy
If your feedback is positive and less than mine you can pay half now - the other half when it arrives and you are 100% happy
If you have no feedback then payment up front please.

 

[hatmoose]

Notes

Minigun Supergun 9-pin in custom 3D printed case - all authentic top quality components from Digikey/Mouser/RS) - JAMMA edge connector is from local NZ supplier tested by me for 1000+ insertions - don’t worry, you won’t get the one I did the insertion testing with, that one is mine, yours is unused except for testing. Case is 100% custom redrawn from Pacifier, loads of cool features to find.

Meanwell RT85a power supply in custom 3D printed case - Power supply from Digikey, invoice available, High Voltage side crimps crimps are genuine AMP PIDG, internal wiring is 16AWG silicone for heat resistance , pins/shells are genuine molex, IEC309 socket is from local NZ supplier extensively safety tested by me, right angle adapter so the cable lies flat I found in a big box of bits from 1996, +5v adjuster has been repositioned to front of shell and replaced with genuine Brouns variable potentiometer, has detent at 5v to prevent accidental overvoltage, knob is knurled aluminium. Case is 100% custom print, designed to either lie flat or on its side

Power cable is custom for this application, It’s been made so it can’t be plugged in wrong, heat shrink at ends is glued inside so it won’t slip, pins/shells are genuine molex minifit JR, wires are 18AWG PVC for abrasion resistance

CPS1 6-button cable is custom for this application, heat shrink at ends is glued inside so it won’t slip, pins/shells are genuine JST, wired 20AWG PCV for abrasion resistance

CPS2/3 6-button cable is custom for this application, pins/shells are genuine hirose (CPS2 end) and JST (Minigun end), wired 20AWG PVC for abrasion resistance

4-player adapter uses cheap DB15 plugs. Case is 100% custom

PGM 4-player cable is an floppy disk cable

6 button controller is from a sega megadrive with a genuine SNK 15 pin cable grafted on - you will not win any tournaments with this. Works perfectly, For testing, Button 5 can be used for neogeo select and etc.

9-pin to SCART cable is cheap — you may want to replace this with a premium one from retro access/RGC at some time. Works perfectly, for testing.

SCART to BNC converter is for Sony PVM owners, Case is 100% custom

No IEC309 (mains power cable) is included - there are so many different power standards around the world this was not practical
No BNC Video cables are included
No RCA audio cables are included
IMPORTANT NOTE - This setup uses a Meanwell RT85a power supply. Some people report ground loop interference on analogue from Meanwell power supplies. I have a Sony BVM E1E, and a 14M2, and JVC BM-H2000PN and have had no Ground Loop Interference problems with this setup

 

[hatmoose]

Bump and price drop down to $US350 (withdrawn shipping is too expensive, would be more like $400 shipped)

 

[hatmoose]

Try-weakly bump

 

[hatmoose]

Hi Team - withdrawn from sale because postage is now just plain silly - will try again later when things calm down a bit