What's new
By:
Filters

FS Primal Rage PCB Enclosure - Preorder/Interest Check

For Sale
I'll keep my order, no worries on the wait, sorry this happened!

Just for curiosity's sake what laser model was it that self destructed, so we can avoid that one, and which laser are you looking at purchasing? I've been curiously looking at lasers, specifically since I found that diode lasers seem like they can cut this matte black acrylic you designed these with -- I love that look. I'm not sure if diode is the way to go for hobby projects like this, especially since I don't know the thickness that those can cut in this matte black, but any recommendations would be cool to hear.
 
I'm so sorry to hear! I will keep my order open. Again, please take your time. Glad things were not worse! Still very excited for this, but do not worry about the delay!
 
What's this? The rest of the acrylic? :D

The good:
The quality is great, and is consistent compared to the acrylic I personally cut. The PR logo cutout pieces have also been retained, and will be included with your enclosures.

The not so good:
I assumed the acrylic thickness would be consistent enough that I didn't need to do a thorough receiving inspection, but this lot was a full 1mm thicker than what was delivered for my personal enclosure! Fortunately, this means a more robust case, but all the side brackets and [some of the] pads have to be reprinted. I started the brackets today and am about halfway done, then on to the pads.

Based on where things are today, the February timeline should be no problem, but expect to see things start shipping next week! I appreciate everyone's patience; future enclosure runs should go smoother (the new laser upgrade should help).


1705637170043.png
 
plasticfactory said:
What's this? The rest of the acrylic? :D

The good:
The quality is great, and is consistent compared to the acrylic I personally cut. The PR logo cutout pieces have also been retained, and will be included with your enclosures.

The not so good:
I assumed the acrylic thickness would be consistent enough that I didn't need to do a thorough receiving inspection, but this lot was a full 1mm thicker than what was delivered for my personal enclosure! Fortunately, this means a more robust case, but all the side brackets and [some of the] pads have to be reprinted. I started the brackets today and am about halfway done, then on to the pads.

Based on where things are today, the February timeline should be no problem, but expect to see things start shipping next week! I appreciate everyone's patience; future enclosure runs should go smoother (the new laser upgrade should help).


1705637170043.png
Click to expand...
🔥🔥🔥 So pumped dude!!!! 🙌🏼
 
Man, getting the cutouts too is so cool! So excited for this!
 
plasticfactory said:
What's this? The rest of the acrylic? :D

The good:
The quality is great, and is consistent compared to the acrylic I personally cut. The PR logo cutout pieces have also been retained, and will be included with your enclosures.

The not so good:
I assumed the acrylic thickness would be consistent enough that I didn't need to do a thorough receiving inspection, but this lot was a full 1mm thicker than what was delivered for my personal enclosure! Fortunately, this means a more robust case, but all the side brackets and [some of the] pads have to be reprinted. I started the brackets today and am about halfway done, then on to the pads.

Based on where things are today, the February timeline should be no problem, but expect to see things start shipping next week! I appreciate everyone's patience; future enclosure runs should go smoother (the new laser upgrade should help).


1705637170043.png
Click to expand...
Thank you for the update! Can’t wait to get my case!
 
Hopefully the final update before shipping!

As of now, everything is ready but the mounting feet. Fortunately they are very simple and will print nice and quickly.

I'm swamped with work this week, preparing for a convention next week, but will be test fitting my spare PR board to make sure everything fits and looks good. Assuming that's a go, everything will be packaged over the weekend and shipped next week. If there are any odd little snags, they should be minor and I'll update here.

I apologize again for the hiccups along the way and appreciate everyone's patience. It was a reasonably simple project marred by some misfortune. If I do another round of enclosures I will definitely make a point to have as much ready as possible before doing a preorder.

(ignore the glare on everything, it's under very bright light)

IMG20240131113938.jpg
 
plasticfactory said:
Hopefully the final update before shipping!

As of now, everything is ready but the mounting feet. Fortunately they are very simple and will print nice and quickly.

I'm swamped with work this week, preparing for a convention next week, but will be test fitting my spare PR board to make sure everything fits and looks good. Assuming that's a go, everything will be packaged over the weekend and shipped next week. If there are any odd little snags, they should be minor and I'll update here.

I apologize again for the hiccups along the way and appreciate everyone's patience. It was a reasonably simple project marred by some misfortune. If I do another round of enclosures I will definitely make a point to have as much ready as possible before doing a preorder.

(ignore the glare on everything, it's under very bright light)

IMG20240131113938.jpg
Click to expand...
Hello fella you still takn orders ? How much for these again.
 
plasticfactory said:
I'm digging the renewed interest, thanks guys. I have to knock out this first run before taking any more orders, but I'll PM you both if I wind up with extras, or do another run. I also plan to release the design files.
Click to expand...
Thank you!!!
 
Very close. Test fitting went well, so all the printed parts and cut pieces fit nicely. Two (final) issues:

- the red spacers for the tall standoffs are 1mm too short. I looked over my order history and this was my mistake. Replacements have been ordered, delivery 2/12-2/16.
- I have to reorder one set of stainless screws because the thicker acrylic caused my original specced screw to be JUST too short. Delivery this Thursday.

I've already contacted the sellers about expedited shipping as I'm really pushing to get these sent to you all this week.

Pic attached is my spare PR board with partially assembled enclosure from this batch. I think everyone is going to be very happy with how these turned out.

Everything else is packed and ready to go, pending the final bit of hardware.
 

Attachments

  • IMG20240205141030.jpg
    IMG20240205141030.jpg
    201.8 KB · Views: 50
Last edited:
Dude this is the most delayed Christmas present gratification I’ve ever had. This is FREAKING AWESOME! Can’t wait to get it and assemble this beauty of a case 🙏🏼
 
I appreciate the patience and apologize that it couldn't have happened sooner. At this point, these are 100% ready to go with the exception of a piece of off-the-shelf hardware. As soon as I have a firm delivery date on the hardware I will post a firm shipping date. Hopefully some of the little extras will help :)
 
plasticfactory said:
I appreciate the patience and apologize that it couldn't have happened sooner. At this point, these are 100% ready to go, but can't be assembled without this one last piece of hardware. As soon as I have a firm delivery date on the hardware I will post a firm shipping date. Hopefully some of the little extras will help :)
Click to expand...
I love it man like I say, Christmas still isn’t over because of this so this extends my holiday a little longer 😊🤙🏼🎅🏼
 
Derick2k said:
Wow!!!! Those are looking amazing. Yeah, Im gonna need one of these for my beastly PR PCB. If you have extra kits please let me know where to send $$ :D
Click to expand...
I'm weighing up not using my kit, so could look to transfer my one to you if @plasticfactory was fine for that?

(I've been told from a guy I've bought from before that a dedicated PR will be coming up soon, so weighing up selling this case and my current PR board, as this case would go to waste inside a dedicated cabinet)
 
DRAGONKZ said:
I'm weighing up not using my kit, so could look to transfer my one to you if @plasticfactory was fine for that?

(I've been told from a guy I've bought from before that a dedicated PR will be coming up soon, so weighing up selling this case and my current PR board, as this case would go to waste inside a dedicated cabinet)
Click to expand...
Thanks, I appreciate it. I will take your spot if @plasticfactory is cool with that. :thumbup:
 
You must log in or register to reply here.
Back
Top