Recent content by K0NAM1

  1. K0NAM1

    Finally, multi System 16B (Sega)

    @Apocalypse can you share the DIP switch circuit please, I'm just exploring selector options, thinking out loud is each "on" DIP switch connecting 5v to a pin on the MCU on your multi PCB? I'm guessing the @Frank_fjs selector used an onboard MCU to directly drive the relevant pin on the multi...
  2. K0NAM1

    Finally, multi System 16B (Sega)

    @Apocalypse could I please change to V1, I'm on the list as rthorntn
  3. K0NAM1

    Minigun Supergun - An Open Source Supergun

    I used @Frank_fjs DIN to SCART PCB and an off the shelf DIN cable, works great.
  4. K0NAM1

    Minigun Supergun - An Open Source Supergun

    @klee123, @evilsim is da man!
  5. K0NAM1

    Minigun Supergun - An Open Source Supergun

    It depends on your knowledge level but a logic probe is a pretty cheap and easy to use troubleshooting tool: https://www.amazon.com.au/Elenco-LP900-625-Logic-Pulser/dp/B0002E7X5O You basically connect it to your PSU 5v and when you touch a pin or PCB contact you can hear the logic, or the audio.
  6. K0NAM1

    Minigun Supergun - An Open Source Supergun

    @klee123 all good, did you get it from ebay or someone on here? I had no audio on the minigun because I decided to leave out the audio jack, the audio jack has a switch in it so even if you don't use the jack you need it to get audio out of the DIN. If you bought yours assembled then it's not...
  7. K0NAM1

    Minigun Supergun - An Open Source Supergun

    @klee123 did you solder the minigun yourself?
  8. K0NAM1

    Minigun Supergun - An Open Source Supergun

    Gotcha, CPS2 definitely doesn't need -5v and Denjin Makai II looks like it doesn't need it either, all my old Konami boards need it.
  9. K0NAM1

    Minigun Supergun - An Open Source Supergun

    What arcade board are you using, some of them need -5v (minus 5v) also?
  10. K0NAM1

    Minigun Supergun - An Open Source Supergun

    Yes, the DIN connector on the minigun carries sound.
  11. K0NAM1

    Australian Roll Call / Registry / Deals Thread

    Thanks @xodaraP, is there an easy way to test the gnd loop on a VSHG, continuity between point A & B but where is A & B?
  12. K0NAM1

    Australian Roll Call / Registry / Deals Thread

    Thanks @xodaraP I have continuity pcb - usb --------------- 1 red - [+] 2 wht - [D-] 3 grn - [D+] 4 blk - [shield] 5 blk - [shield] Now pin 4 on the USB [-] is not connected but I was thinking that that doesn't matter if the PCB is getting negative (PCB pin 4) from the shield wire? The white...
  13. K0NAM1

    Australian Roll Call / Registry / Deals Thread

    Thanks @Nimmers Do we have any idea if there are spare PCB's available for the HSN-0011? Any Aussies out there (that have upgraded a VSHG) keep the original PCB? It's either the cable or the PCB thats faulty.
  14. K0NAM1

    Australian Roll Call / Registry / Deals Thread

    Thanks @djsheep @mR_CaESaR @xodaraP So I have this third DOA VSHG, ironically the one I paid a lot more for on YAJ (but hey it had a box)! It could be the VSHG PCB thats failed. Any Aussies want to cleanly mod it for me, I'm thinking to just convert it to a DB15?
  15. K0NAM1

    Open Source USB2DB15 for Supergun adapter

    This looks great, I would love to help with this and be involved. I can solder SMT and I'm no stranger to DIGIKEY or PCBWAY. I have some UD-USB but I would love persistent button mapping.
Top