mugen_ketsueki
Professional
If anyone has a JVS I/O Type 3 board (Sega 837-14572) for sale with the cables and etc please let me know. I am needing this to be able to play my Ring Edge 2 Multi since the Capcom I/O will not work with it.
WTB JVS I/O Type 3 board (Sega 837-14572)
- Thread starter mugen_ketsueki
- Start date
Want To Buy
exactly what cables are you expecting to come with it?
these were shipped in cabs and attached directly to the whole cab harness.
mugen_ketsueki
Professional
USB at least cause imma use it on a supergun so i know a kick harness would need to be made but at least something so i can play the games on it with either 4 to 5 buttons
you're going to need to make a lot more than a kick harness..
you do know what the Type 3 JVS IOs look like right?
it uses the same pinout as the type 1
if you're trying to hook this up to a supergun you're going to have to build a whole custom JAMMA harness for it.
you do know what the Type 3 JVS IOs look like right?
it uses the same pinout as the type 1
if you're trying to hook this up to a supergun you're going to have to build a whole custom JAMMA harness for it.
skate323k137
Enlightened
Instead of a supergun, for a non cabinet Ringedge setup I use a type 3 IO with @Mitsurugi-ws S-JIHP board. I made DB15 to DB25 adapters and use neo style joysticks (or UD converters). For AV I just use normal VGA monitor and PC speakers.
Last edited:
psychicdrive
Student
I'd suggest a SEGA JAMMA to JVS IO for this purpose
I might have a spare rev b / something with a jamma edge. Not sure if ringedge works with it, but I could check
mugen_ketsueki
Professional
Please let me know if it does.
mugen_ketsueki
Professional
Geez if i knew anyone who would do that that be great lmao.you're going to need to make a lot more than a kick harness..
you do know what the Type 3 JVS IOs look like right?
it uses the same pinout as the type 1
if you're trying to hook this up to a supergun you're going to have to build a whole custom JAMMA harness for it.
I think it should, another member said it did iirc. I think the RE checks the io id to be a sega. This would probably be the easiest route for the OP to go. I know I have a couple of these but God knows when i can find them lol. I have been redoing all my consoles so have sorta gone down a rabbit hole, getting them mods etc...
Last edited:
mugen_ketsueki
Professional
if you have extra that you find let me know
Ill see if I have one at home this weekend, if not, they are in storage units, so that will take a bit longer to go through. Will let you know.
mugen_ketsueki
Professional
Rev B seems fine, I booted up a couple games. It plugs in via the jamma edge. I think you have to add kicks to one of the headers. They were like $30 all day on YAJ but here’s one for $60 shipped https://www.ebay.com/itm/154094415352 though I didn’t look for more than 5 seconds!
Last edited:
mugen_ketsueki
Professional
Vga is for video? I assume? Tho I don’t need it? Mainly the USB to the JVS port then get a kick harness made correct?
I ran video direct to my source but presumably yes you could run video into that vga port. Usb from one of the two USB ports to the jvs port on the ringedge. This seems to be the cn3 pinout for kicks; some kick buttons are already on the jamma edge apparently https://wiki.arcadeotaku.com/w/JVS#Sega_838-13683-93
mugen_ketsueki
Professional
may i ask if you know based on the multi is mainly all of them around 4 to 5 buttons? if so i wouldn't need a kick harness then if it mentions 5 buttons is on the Jamma.
I haven’t payed much attention to that
mugen_ketsueki
Professional
Ok no worries but thank you for confirming with me.
skate323k137
Enlightened
Buttons 1 thru 5 are on the JAMMA edge, you'll need an extra loom for B6. Having 1 thru 5 on JAMMA made the rev B JAMMA IO very compatible in blast city cabinets.