Ps. I’m still making (slow) progress on the system 18 OLED icons. Working on Clutch Hitter right now. I’ve got about 4 more remaining then I’ll release them to @Frank_fjs
SEGA SYSTEM-16 MULTI - OLED BASED GAME SELECTOR
- Thread starter Frank_fjs
- Start date
- Status
Lovely!
ShootTheCore
Legendary
Irem M72! Irem M72!! Irem M72!!! 
M72 I shall do with a few caveats...
I won't be building nor distributing them.
The cost of the first round of prototype PCBs and parts is covered.
It will be open sourced for people to assemble their own.
Reason being that I don't own the multi so it's of no use to me.
I won't be building nor distributing them.
The cost of the first round of prototype PCBs and parts is covered.
It will be open sourced for people to assemble their own.
Reason being that I don't own the multi so it's of no use to me.
I'm a little excited, I just did an order for SMD assembly. Never done it before, and while it cuts into profit (which honestly is very slim) it does give me back time. Time I don't need to spend soldering, yay! Just the main PCB and only the surface mount components, but all that's left for me to do by hand is the USB C connector, 3 headers and the OLED. Will save a heap of time and be nice to have machine soldered boards.
Sp33dFr34k
Champion
Nice job
Hedonism Bot 2.0
Grand Master
Definitely in for one of these for the system 16 multi.
Edit: one with the remote please.
Edit: one with the remote please.
Last edited:
Ignore the USB connector, header pins etc, add an SMD IR receiver top right (didn't have a 3D model of it) and that's what I'm getting factory soldered.
Only ordered 5 units as a test run and if it works out well I'll be doing all my orders this way. Will be a huge time saver and allow me to pump out orders a lot quicker.
PCB needs to be green solder mask, moved all SMD components to the top layer and changed the 3 x tactile switches and IR receiver to SMD components to accommodate the assembly service.
Oh, and 3 of my OLED screen orders have arrived in Australia so it won't be very long at all till I despatch paid orders. Thank you for your patience.
Only ordered 5 units as a test run and if it works out well I'll be doing all my orders this way. Will be a huge time saver and allow me to pump out orders a lot quicker.
PCB needs to be green solder mask, moved all SMD components to the top layer and changed the 3 x tactile switches and IR receiver to SMD components to accommodate the assembly service.
Oh, and 3 of my OLED screen orders have arrived in Australia so it won't be very long at all till I despatch paid orders. Thank you for your patience.
@nonosto
@KalessinDB
@mncmt
@LHantz
@kuze
@tom5151
@archimage
Your orders are being shipped this Friday.
@KalessinDB
@mncmt
@LHantz
@kuze
@tom5151
@archimage
Your orders are being shipped this Friday.
Last edited:
I 
you.
Would you hate me if I told you you were missing one? That being, Pontoon.
They look fabulous. I'll load them up on the OLED screen tonight.
you.Would you hate me if I told you you were missing one? That being, Pontoon.
They look fabulous. I'll load them up on the OLED screen tonight.
Well shoot. I didn't realize that was part of the list. The system16 site didn't even have it listed.
I'll bang that one out now.
And here you go:
@Frank_fjs Also, feel free to invert that Moonwalker. I couldn't decide which way looked better.
Last edited:
This made me a happy camper. Finally seeing some OLEDs rolling in. Been very hit and miss with a lot of suppliers and postage but have found a reliable source through ordering from a wide variety of sellers.
Version 2.00 firmware available now.
See second post of this thread for programming instructions and the HEX file download.
Notable changes:
- Attract Mode feature
- Program IR remote feature
All units from this point on ship with this firmware.
See second post of this thread for programming instructions and the HEX file download.
Notable changes:
- Attract Mode feature
- Program IR remote feature
All units from this point on ship with this firmware.
- Status