What's new
By:

US to ASIA B board conversion question

M

magicman

Student
Joined
Mar 12, 2025
Messages
39
Reaction score
12
Location
Coral Springs, FL
Hi, so I have a US Marvel vs Capcom rev 6 B board that was badly damaged by the battery leak. I picked up another rev 6 B board for Street Fighter Zero to convert Marvel vs Capcom to but I accidentally bought a ASIA B board. I only have a US A board. I've already transferred over the ROMS, the PAL G, configured the InfiniKey when I realized the different connectors on the bottom. Do I have to get an ASIA A board? Can I desolder the connectors and transfer them over ? BGS1 & 2 were socketed on the US board, they're soldered to the ASIA board, also spotted some caps not populated.


Basically, US B board to ASIA B board, same revision. Aside from the physical connection to the A board, is there anything different? Anything region locking?
 
The only difference is the connectors and they can be swapped as I have done this and can confirm it worked. It's a pain in the a.... though even with a desoldering station.
 
Agree the only difference is those connectors - there are 4 connectors with 96(?) pins per connector.

You dont have to change all the connectors of course (edit, see below I did not recall correctly, all 4 DO need changing). IIRC the Asia B board has one weird long connector, and 3 standard ones.
So thats only (only?) 96 pins to desolder the weird long one from the Aisa B board, 96 more pins to harvest a standard connector from a donor board, then 96 pins to solder back on.

96 (or 192) pins is reasonable amount of desoldering with a decent desoldering station. Might be worth looking at a .8mm nozzle to speed things up. Doing this by hand with braid/pump would be very time consuming and error prone

If you dont have a donor board to harvest from you could source a replacement connectors with the correct dimensions from here. Not identical to the OEM part, but electrically and mechanically compatible
https://www.digikey.co.nz/en/products/filter/connectors-interconnects/307?ColumnSort=0&ColumnSort=0&FV=7004c4,1600032,8d00002,ii3|2172,ffe00133,1140050&FV=7004c4,1600032,8d00002,ii3|2172,ffe00133,1140050&page=1&page=1&pageSize=25?k=eurocard connector&pageSize=25&pv589=25&pv589=25&quantity=&quantity=&s=N4IgTCBcDaIKYFcBOB7AxgQyQEwARpQDtC40AXFJEAGhBroF0BfIA&sf=0&sf=0&sv=0&sv=0
 
Last edited:
Desoldering all 4 connectors is a pain.

Asia connectors are exactly inverted from usa.
So a board connectors on b and b on a with one oddball length one.
Damn capcom.

If you change your mind I am in need of a working asia B.
I made this mistake, too.
 
Can confirm - one oddball length one AND the other three exactly inverted

IMG_0028.pngIMG_0027.png
Asia = top, USA = bottom in these photos

That being the case, you DO have to change all the connectors, 400 pins + 400 more pins for donors, + 400 pins to solder back on.

Way too much work for me...
 
Last edited:
I spent the better part of 2.5 hours yesterday just to remove 2 connectors from the old damaged US board. I still have 2 more to go and then on to removing the 4 connectors from the Asia board.

It's 96 pins, x 4 ... then I have to do it again on the new board 96 x 4. That's 768 pins to desolder, then 384 to solder again.

I'm using a Hakko FR-301 desoldering gun, I love this thing... but it is still taking forever lol

If I wasn't such a fan of the original MvC, I probably wouldn't be bothering. This is a ton of work, and if the logic chip by the battery hadn't been so badly damaged around the traces, I would have just swapped that over for much less work.


What I'm still not sure about is the socket BGS 1 & 2 on the old US board vs the soldered BGS 1 & 2 on the Asia board. Also a few 'CCX' caps populated on the US board that are not populated on the Asia board.
 
Spent about another hour going through removing the third connector. What I've found is that the battery leakage that affected pins on the connectors makes it much harder to desolder. I definitely plan to take some pictures of this whole process, so far all I have been doing though is just endless desoldering and cleaning of my desoldering gun.. not much picture worthy stuff going on yet lol
 
You must log in or register to reply here.
Back
Top