Patience, sir Was that you that wrote looking also for CPS1 InfiniKey? If so, that is the reason for delay.I need buy some infinikeys but are out stock.
Where I can buy 5 infinikey . I wrote undamned but never received answers.
Paradise should re-stocking soon. I'm just waiting for payment before I ship out.
I thought I read somewhere that the resistor you can find attached to the pins of cn2 on some rev 3/4 boards was there to help with key programming.
Edit: Nevermind, you call it out in your install video, so I'll take it off as well
The post was edited 1 time, last by Sp33dFr34k ().
I'm having a problem with an Infinikey and a grey B board running Street Fighter Zero 2 (960227 ASIA)
I'll first say that I've installed a few Infinikeys over the past few months but this is the first one that's given me a problem.
The B board rev is 93646B-7
From checking progettoemma.net the MAME name for this code is SFZ2N - in the Infinikey Game Select file this refers to SZ2N
So I set the jumpers accordingly by bridging the required pads - (numbered from 7 to 0) - 1010110
I then removed the battery from the B board - I should say that before I removed the battery the game was working just fine.
After removing the battery I shorted the three pins for EXC1 as I always do.
I then installed the Infinikey to the rear of the board (CN9, orientation was correct, etc), plugged in the B board and got a slightly out of sync blank display. I re-checked the Infinikey instructions and realised that I had forgotten to jumper the pad for 'open for 93646B-5' - so I jumpered that. Powered on again - the sync was then stable but still a black screen.
Checked everything again a few times and am now stumped.
Any ideas please what could be wrong? I've had a long day and am a bit tired so maybe I've missed something obvious.
EDIT: Forget all of the above, it was my mistake. As noted, I obtained the version of the game by looking at progettoemma.net - this stated that the MAME name was SFZ2N. That's wrong as I discovered when running ROMIdent on a dump of program EPROM 3 - the ROMIdent name is SFZ2A. Once I set the jumpers for that on the Infinikey the board booted just fine.
My apologies. Did I say I was tired?
The post was edited 2 times, last by VectorGlow ().
I tried contacting undamned, he hasn't gotten back to me. (I'm sure he is busy) I want to buy 10 of these if possible.
So, I'm trying to remove an InfiniKey (Mobo Rev.7 install) for a Darksoft CPS2 install, but try as I might I straight up can't remove the thing. How far do I have to go to fully disable the InfiniKey so a Darksoft CPS2 install will work? I would like to remove as few components as possible from it in case it gets reused on this board in the future.
Edit: I worked it out and got it removed. Went about it wrong from the start. I should have kept adding solder and turn it into one big molten mess instead of trying to remove the solder.
The post was edited 4 times, last by Rotanibor ().
Have a weird issue with a X-Men Cota. I installed infinikey's in other boards and they work fine. This particular board though is a mess. It'll work, then green screen when I power it. I removed EXC1 & EXC5 completely. I took off the electrolytic cap and then soldered it back in.
This particular Infinikey I soldered to much with and set aside, I have a better soldering iron and solder now.. Maybe I damaged it? I am using the other side of it with this install. Here is a picture of it. Any clue what this could be? Picture does not show the removed EXC1 & EXC5.
Swapped for another Key. Fixed it. I messed up the other.