What's new
By:

Home Arcade System

The HAS is back in stock along with a few new items!

Most importantly, I now offer covers for the Mean Well RT series of PSUs in two variants, both are super easy to install.

54163886618_b01464fc94_c.jpg

54164064015_d7e8d70286.jpg
54164061535_d8103bab70.jpg
 
Wow! It took some real effort to pull my cart back from like $950 to $340. 😁 Lots to like, including broader access to PSU covers, but I think I'm happiest for Egret-compatible RECO.

Is RECO an initialism, or just a Mushihimesama reference?
 
  • Love
Reactions: RGB
I've got quite a few items in the cart, so I'm guessing I'm over the order minimum (if there is one). Is there a region lock, I'm getting this error message? Shipping is to California.
HAS no shipping.jpg
 
This is strange, because there isn't order minimum (except for the UK) or region lock. Maybe you have an item in your cart that has been sold out? Also, the max order value is set to $800, I didn't set shipping rates for anything above that.
 
I've had my HAS v5 in storage for about 2 months while traveling and decided to break it out yesterday. Unfortunately I'm having issues with getting it to work with boards I've used in this setup in the past. When powering on it shows general info before showing the voltmeter for a few seconds, then the screen turns off. I don't remember the voltmeter before so I dont think it's seeing the board connected.

My previously working setup was Jamma PCB --> HAS --> OSSC so I don't think it's an issue with the Csync settings.

I've tried multiple boards that I know work and two different JAMMA extenders, which led me to believe it may be an issue with my HAS. Any recommendations for further troubleshooting? Unfortunately I don't have another supergun to test so it may be a good opportunity to buy another HAS... lol.
 
I'm sorry to hear about the trouble. Don't order another HAS, I'm pretty sure this is a settings issue.
1RegretBeetle said:
When powering on it shows general info before showing the voltmeter for a few seconds, then the screen turns off. I don't remember the voltmeter before so I dont think it's seeing the board connected.
Click to expand...
This behavior is normal, the OLED turns off after 10 seconds.
1RegretBeetle said:
My previously working setup was Jamma PCB --> HAS --> OSSC so I don't think it's an issue with the Csync settings.
Click to expand...
1. What kind of AV cable do you use?
2. Can the OSSC detect the video signal?
3. Could you take a picture of the Video Menu of the HAS?

https://rgbslab.com/pages/has-instruction-manual
 
RGB said:
I'm sorry to hear about the trouble. Don't order another HAS, I'm pretty sure this is a settings issue.

This behavior is normal, the OLED turns off after 10 seconds.

1. What kind of AV cable do you use?
2. Can the OSSC detect the video signal?
3. Could you take a picture of the Video Menu of the HAS?

https://rgbslab.com/pages/has-instruction-manual
Click to expand...
Thanks for the help! Will follow-up in dm!
 
  • Like
Reactions: RGB
I received my package yesterday and it did not include any of the Power Supply Cover fuses. Can you clarify which fuse I would need for the RT-85A PSU.

Thanks
 
nwilloughby said:
I received my package yesterday and it did not include any of the Power Supply Cover fuses. Can you clarify which fuse I would need for the RT-85A PSU.

Thanks
Click to expand...
  • RT-65A:
100-120VAC - 2.5A
220-240VAC - 1.6A
  • RT-85A:
100-120VAC - 3.15A
220-240VAC - 2A
  • RT-125A:
100-120VAC - 4A
220-240VAC - 2.5A

Please make sure you read the assembly instruction, the fuse information is there - https://rgbslab.com/pages/psu-cover-assembly

There should be a piece of gray foam inside the bag with screws and rubber feet. The fuses are stuck into that piece of foam, please check and let me know.
 
Could you tell me the part # for the connector used on the module end of the 3P4P harnesses?

It looks like it's some sort of 0.1" polarised connector but I'd like to make sure I use the right one for some harnesses so it latches in the module correctly.
 
It's a 20pin 2.54mm pitch IDC connector, the part name is 09185207903, but you can use other brands, it doesn't matter.

The one used in the 3/4 player harnesses is JST RA-2011.
 
Last edited:
You must log in or register to reply here.
Back
Top