CPS-2 Custom Metal Case -Pre-Orders open now
- Thread starter hursit
- Start date
Yes you can order. But you have to wait 1 week for painting...
KalessinDB
Grand Master
Gah, finally trying to install this... My Noctua fan is 3 pin and the CPS2 fan is 2 pin. I thought I remembered there being a way to fix it somewhere in this thread but I can't find it. Anyone able to help?
MoppelTheWhale
Grand Master
i can't look without opening it up comletely, , but i think i just connected it so that only red and black on the noctua were connected - i didn't even change the connector if i remember correctly - yellow should be the wire for speed control.
Takosuke
Professional
Yup I did the same as the above. The clearance to put the case back is scary though, it barely fits :p
KalessinDB
Grand Master
You guys are very correct, I did the same. Oh GOD the clearance is tight reassembling it. But now? They're both cased and waiting for the CPS1 multi and case, then I get to play Jenga putting those 3 and a switcher into my big blue.
Also, the LCD fit just fine in my CPS2 case.
Also, the LCD fit just fine in my CPS2 case.
Attachments
Yeah ,there is only 2-3mm space between Fan and the mainboard as the original. It is little bit hard but not impossible to make it
They look awesome.
By the way, i really do not know how i will fix the LCD fitting problem
.Myabe i will ask to people the LCD measurements that have cps2 multi kit.
KalessinDB
Grand Master
One thing I did notice though, 2 of the standoffs for the motherboard didn't line up right with mine. I'm not super concerned, 6 should be enough, but it was kinda weird.
Do you have pictures ? or did you take pictures before you close the case
Takosuke
Professional
I’ll post the measurements. One way is to make the space just a tiny bit larger, so it’s not too much empty space for those that the default cut fits and just enough for us with slightly larger screens. I wonder If has to do with where the multi kits were bought from (US source vs EU source).Yeah ,there is only 2-3mm space between Fan and the mainboard as the original. It isBy the way, i really do not know how i will fix the LCD fitting problem
Myabe i will ask to people the LCD measurements that have cps2 multi kit.
KalessinDB
Grand Master
Ah didn't think to take pics, sorry. It's the 2 that go between the connectors, midway up the sides of the board. It's buttoned up now so I'm unlikely to worry about it too much, especially once I get it put in to my cabinet permanently.Do you have pictures ? or did you take pictures before you close the case
I will check it out. Thanks.Ah didn't think to take pics, sorry. It's the 2 that go between the connectors, midway up the sides of the board. It's buttoned up now so I'm unlikely to worry about it too much, especially once I get it put in to my cabinet permanently.Do you have pictures ? or did you take pictures before you close the case
I need the New LCD measurements.
@Takosuke and @KingSopz , if you have Measurements device, please give me the detailed measurements
With this device
Takosuke
Professional
I have 7cm for the length
noonan2678
Student
I have the same LCD issue and have not assembled yet. Has anyone done so? Curious of the tools that were used. My thought is a dremel...not sure what bit though.
Happy to send the measurement of my screen as well. I have a laser measurement device that might work.
Happy to send the measurement of my screen as well. I have a laser measurement device that might work.
BroadwayJose
Professional
Finally ready to assemble this case and I have a question about the test button connections. My understanding is the signal wires can be soldered wherever on the button. Where is a proper spot for the ground wire?
Also +1 for the LCD not fitting correctly but sounds like I can fix that with a dremel or something similar so I'm not too worried.
Also +1 for the LCD not fitting correctly but sounds like I can fix that with a dremel or something similar so I'm not too worried.
!!!Now we need the cps1 case
!!!
BroadwayJose
Professional
Bumping this up as I'm still looking for an answer on this. Instructions were a bit vague and I haven't seen anything definitive in any install pics I've seen so far. Really looking forward to putting this build behind me and enjoying my multi. Thanks.