Home Arcade System
- Thread starter RGB
- Start date
I use an RT-125A with my HAS. It works fine, however boards that consume less than 1A (MVS MV-1C for instance), have trouble since the PS requires a minimum load to work.
SEGASHIRO
Professional
I would love to pick up one of those finished adapters with my next HAS order (when ever the next run isFinally received my PCBs from OSH Park
With this adapter you can connect HAS with the OSSC using a standard VGA cable.
You can also use a VGA->BNC cable to connect it directly to PVM/BVM monitors.
Order the PCBs from here. If there is enough interest I can start stocking those, too.
Edit: The adapter comprises of a female VGA connector (HD15) and a 1x8pin 18mm goldpin header. The header pins need to be moved a bit so that you end up with 10mm long pins that connect to HAS, and shorter ones that will go to the adapter. You will also need two 15mm long screwed spacer sleeves and bolts to install the adapter.
SelfDeniedHoarderz
Professional
Would it be possible to have a portable design like Windy Gaming ATP300 where it has built PSU and a rugged enclosure for tournament setup?
If you can make it even smaller than Windy Gaming supergun, it would be true feat as I dont see any supergun on the market that is actually smaller than that (given HAS supergun has to comes with bulky Arcade PSU as the main power source).
If you can make it even smaller than Windy Gaming supergun, it would be true feat as I dont see any supergun on the market that is actually smaller than that (given HAS supergun has to comes with bulky Arcade PSU as the main power source).
The Spaniard
Professional
I read through all 40 pages in the last couple of days, was just going to ask about something like this.
Ideally what would make this supergun awesome would be portability fully enclosed with all ports like the UD-decoder mounted onto a flat surface just like a console. And of course the possibility to use a laptop brick or some sort of pico PSU that could fit inside the case and only need to have a cable to plug in to the back of the enclosure.
Was actually thinking in my head if I have the skills to make something like this that I envision, this supergun is on my wish list for sure.
Ideally what would make this supergun awesome would be portability fully enclosed with all ports like the UD-decoder mounted onto a flat surface just like a console. And of course the possibility to use a laptop brick or some sort of pico PSU that could fit inside the case and only need to have a cable to plug in to the back of the enclosure.
Was actually thinking in my head if I have the skills to make something like this that I envision, this supergun is on my wish list for sure.
@modology, @The Spaniard - I built a few superguns like that in the past - Supergun showcase!
I wish I could build more of those, but it's just too time consuming and expensive this way. I came up with HAS as a less expensive solution that I could offer to more than just 4-5 people per year. The biggest obstacle for me is the JAMMA harness. I hate building those, and I'm not satisfied with the pre-made Chinese ones, I couldn't offer them with my device.
I wish I could build more of those, but it's just too time consuming and expensive this way. I came up with HAS as a less expensive solution that I could offer to more than just 4-5 people per year. The biggest obstacle for me is the JAMMA harness. I hate building those, and I'm not satisfied with the pre-made Chinese ones, I couldn't offer them with my device.
Sp33dFr34k
Champion
Holy crap, very clean looking supergun Mike, I like it!!
Damn, HAS you been holding out on us 
Why don’t you do an interest check post? I would love get 2 supergun setups like that one. Need one for the pvm and one for the plasma.
Let men know if decide to make a run of these, minus the Jamma Harness is fine for me. Maybe if you get enough peeps to make it worth the time??
Maybe incorporate a space for peeps to install/integrate an Ossc into it??
Why don’t you do an interest check post? I would love get 2 supergun setups like that one. Need one for the pvm and one for the plasma.
Let men know if decide to make a run of these, minus the Jamma Harness is fine for me. Maybe if you get enough peeps to make it worth the time??
Maybe incorporate a space for peeps to install/integrate an Ossc into it??
J
jassin000
That!
IMO the ultimate HAS enclosure would be one that included a space for the OSSC and the PSU.
Blackfish
Professional
I was thinking the same thing
The Spaniard
Professional
SEGASHIRO
Professional
Hot damn that thing looks awesome. I'd totally be down for one.
Joko3
Legendary
That thing is beautiful! I’m overall happy wIth the MK30 Jasen Hicks built me, but damn this one is cool! I would definitely buy one given the opportunity : D
Joko3
Legendary
That would be awesome! With some Saturn controller (or maybe USB) inputs too you’d have the perfect portable supergun!
The Spaniard
Professional
That was what I had envisioned, 2 sets of saturn ports and 2 sets of USB ports on the front, maybe the 4 player ports as well or have those around the back as an extension of some sort. Would be great for tournaments for almost any system instead of limiting yourself to one system like UD-CPSII which is awesome but just serves one purpose for one system only.
vooch
Beginner
As nice as a sleek all-in-one unit would be, I still want the standard HAS. Since production times are an issue and I'm waiting for HAS orders to open up again, I'm all for availability over portability. The power supply thing isn't that big of an issue considering a lot of boards aren't in any enclosures when they're played on a supergun. But it would be really nice to have a way to somehow combine the HAS with the OSCC.
Sp33dFr34k
Champion
For me the HAS goes to the gscartswitch via 8 pin mini din to scart, then to OSSC. Don't really see the need of having an all in one thing for that especially since you can't use the OSSC for anything else once it's integrated.
About the "full" HAS supergun solution - sorry guys, not happening soon, too much stuff on my plate at the moment. We can come back to this in a few months. One thing is certain, though - it would be extremely limited in quantity, 3-4 units tops, just to see how it goes for me, but I know it's not something I seek to do in larger quantities.
SNK-NEO-GEO
Enlightened