What's new
By:
Filters

Is it possible to play Eco Fighters without a spinner?

Bonky said:
I have played Eco fighters with the adapter of Brizzo "for puzzle bobble".
Need some modification and it's working ;)

The pcb in pictures on the last post, i have it later and i just played puzzle loop 2.
Click to expand...
i have Brizzo's adapter. what do i need to do to get it working for eco fighters?>
 
found it in a box ^^
 

Attachments

  • IMG_20220820_175824.jpg
    IMG_20220820_175824.jpg
    184.6 KB · Views: 86
Jamma Bouton 3 ---- right on Brizzo's adapter
Jamma Bouton 1 ---- left on Brizzo's adapter
Jamma left ---- Go to left on the upper adapter
Jamma right ---- Go to right on the upper adapter
 
Bonky said:
Jamma Bouton 3 ---- right on Brizzo's adapter
Jamma Bouton 1 ---- left on Brizzo's adapter
Jamma left ---- Go to left on the upper adapter
Jamma right ---- Go to right on the upper adapter
Click to expand...
the upper adapter is just a passthru, correct?
 
Bonky said:
Jamma Bouton 3 ---- right on Brizzo's adapter
Jamma Bouton 1 ---- left on Brizzo's adapter
Jamma left ---- Go to left on the upper adapter
Jamma right ---- Go to right on the upper adapter
Click to expand...

this does not work. the arm just keeps spinning. you also lose button 1 so you can not go into input on service menu. did you lift the pins on the brizzo adapter or did you just solder button 1 and 3 directly to it>?
 
Last edited:
Thats working for sure ;).

I lift 4 pins (left, right,b1 and b3 to the jamma).
White and green (left and right to the jamma connector) go to the upper pcb.
Under white and green, solder on the brizzo adapter, the wires left and right go to jamma 1 and 3.
For b1 look the upper pcb
Make the same adapter (with all wires)
 
Last edited:
Bonky said:
Thats working for sure ;).

I lift 4 pins (left, right,b1 and b3 to the jamma).
White and green (left and right to the jamma connector) go to the upper pcb.
Under white and green, solder on the brizzo adapter, the wires left and right go to jamma 1 and 3.
For b1 look the upper pcb
Make the same adapter (with all wires)
Click to expand...
i did exactly that . did not work

edit: it works now.
 
Last edited:
This is what I did. Not working for me. I know in theory it should. I checked my connections and soldering and still just rotates to the left constantly. I made sure there is visible space between the pads and lifted pins. And verified all solder locations are correct.
20220820_200615.jpg
 
i pulled everything off one by one to isolate the issue, and it is that p1 to left input. everything else works as it should

i rewired it and it still has that issue
 
Is it possible to take picture in other position to see all solder wire ? (jamma and see solder on brizzo adapter)
your adapter is fully wired ?
 
Bonky said:
Is it possible to take picture in other position to see all solder wire ? (jamma and see solder on brizzo adapter)
your adapter is fully wired ?
Click to expand...
My pass thru adapter is fully wired. This is a Pic I took half way through , before I tied the left and right to the jamma pass thru adapter
20220820_132924.jpg
 
Edit
the picture i have posted is bad.
I look now the adapter with no beer.

;)
 
Last edited:
i figured it out. i had already lifted the pins to L and R. turns out the culprit was a surface mount resistor going into the Left input was missing. i must have hit it with the desoldering gun while desoldering pins or something. i replaced all the surface mount resistors going to L and R and now it works 100%

thank you very much for your help @Bonky and @West
 
You must log in or register to reply here.
Back
Top