Mahjong controller support on MV1C/MV1B
- Thread starter pierpa86
- Start date
Yes sure: https://makerworld.com/en/models/1223740-mahjong-controller-mvs-neogeo#profileId-1241107
If you goin to use this on AES, close the jumper on board.
Ordered the PCBs, having a friend 3D print the controller shell, ordered the kaihl switches and keycaps. I also ordered some neogeo 15pin cables, is there an easy method to know which wire to solder where?
Going to build two of these, one for my MVS and another for my friend's AES.
Do you happen to know if this would work for Neo Geo CD without closing the jumper on board? Or if it will work on supergun with other arcade boards?
Going to build two of these, one for my MVS and another for my friend's AES.
Do you happen to know if this would work for Neo Geo CD without closing the jumper on board? Or if it will work on supergun with other arcade boards?
Presumably on a MV1B/C with a normal Supergun you need to run two cables from the Jong controller to both the Supergun and the JST connector on the MVS, with the 74LS06 logic in between?
Trying to work out how it all bolts together. I don’t know why, but I want one
Trying to work out how it all bolts together. I don’t know why, but I want one
Do you have a specified screw size?
Also on the bottom of the PCB, is this a kind of top plate it screws into? I didn't see it in the 3D print files.
Edit: I just realized you were using the bracket that came with the original controller.
Last edited:
Kujako
Champion
Do you have a source for the zbf253d's? I can always scavenge them from failed boards, but I don't know of anyplace they can be purchased...Easy:
1) Get OUT pin here.
2) from side connector to 74ls06 input :
3x 22ohm resistor
1x 74ls06
3x zbf253d
3) out from zbf253d to DB15
pin 10-2 and 9
I take it from a mv2f failed board, but you can take from any model of mvs.
i'm not sure about direct substitute:
https://www.mouser.it/ProductDetail/TDK/MMZ1608B102CTD25?qs=pvNC7ksEVIefM6hx9JP%2Bzg==
its a Noise-Suppression Filters so maybe you can try without it
Kujako
Champion
Mouser always lists them as “restricted inventory”, so the times I’ve needed them I always have to scrounge. And yeah, never been too clear on their purpose beyond the FCC saying they need to be there.I take it from a mv2f failed board, but you can take from any model of mvs.
i'm not sure about direct substitute:
https://www.mouser.it/ProductDetail/TDK/MMZ1608B102CTD25?qs=pvNC7ksEVIefM6hx9JP%2Bzg==
its a Noise-Suppression Filters so maybe you can try without it
(for my own notes on CN1)
Code:
CON1
pin 1 - NC (ground)
pin 2 - NC
pin 3 - pin 9 of 2up joystick port
pin 4 - pin 2 of 2up joystick port
pin 5 - pin 10 of 2up joystick port
pin 6 - pin 9 of 1up joystick port
pin 7 - pin 2 of 1up joystick port
pin 8 - pin 10 of 1up joystick port
Can pull VCC from TP2Related: anyone have the JST type and size for CN1? Could always just use dupont connectors...
Last edited:
Unfortunately i got a ransomware attack on my pc yesterday, testing new server and an "hacker" get in to one of my pc 
Dude its not a joke, some one have really done it.
Ok its my fault, but damn its was too fast.
I lost all my file ! nothing really important, i take the important things on cloud. but damn mahjong was on my desktop.
Dude its not a joke, some one have really done it.
Ok its my fault, but damn its was too fast.
I lost all my file ! nothing really important, i take the important things on cloud. but damn mahjong was on my desktop.
My friend OMPeaRetro was able to take your gerber files and make them compatible with kailh choc switches. He did a great job and I have ordered the PCBs, I think this will help a lot of people build a mahjong controller from scratch.
