MiSTerAddons MiSTercade - MiSTer for JAMMA cabinets

[rtw]

@raffy92 please provide a picture of the cable from your supergun to the JAMMA connector. Does your cable looks like this ?

 

[raffy92]

@raffy92 please provide a picture of the cable from your supergun to the JAMMA connector. Does your cable looks like this ?

Yes exactly and for the scart I am using the packapunch rgb for sigma av7000

 

[rtw]

The SIGMA connectors have a small fault, they do not supply GND to pins 27,28, e and f.

You should solder on GND to lthese as well.

 

[raffy92]

The SIGMA connectors have a small fault, they do not supply GND to pins 27,28, e and f.

You should solder on GND to lthese as well

You mean the specific cable that link the controller to the control box ?

 

[raffy92]

Or the « jamma » part that is inside the control box ?

 

[rtw]

I mean the blue connector in the picture I showed. It is missing GND on pins 27,28, e and f.

These pins must be connected to GND.

edit:
Or buy this ?
https://www.ebay.com/itm/175422346525

 

[raffy92]

I see, but I don’t think it will resolve my problem, because I have the same kind of issue when I am using a HAS v5.0 with the Mistercade.

 

[raffy92]

I mean the blue connector in the picture I showed. It is missing GND on pins 27,28, e and f.

These pins must be connected to GND.

edit:
Or buy this ?
https://www.ebay.com/itm/175422346525

Anyway thanks for the advice

 

[raffy92]

I mean the blue connector in the picture I showed. It is missing GND on pins 27,28, e and f.

These pins must be connected to GND.

edit:
Or buy this ?
https://www.ebay.com/itm/175422346525

I checked carefully on my jamma harness 27, 28 are not missing see the following pictures

 

[raffy92]

 

[raffy92]

Does anybody tried to run the Mistercade on HAS v5.0 ?

 

[rtw]

It is good that you have a proper GND on your SIGMA.

I believe I have tried Mistercade but on HAS 4.0, IIRC there were no issues.

Just to clarify, your problem is that while pressing button 1 sometimes button 2 will register as well ?

How are you powering your SIGMA and Mistercade ? Pictures please

 

[raffy92]

It is good that you have a proper GND on your SIGMA.

I believe I have tried Mistercade but on HAS 4.0, IIRC there were no issues.

Just to clarify, your problem is that while pressing button 1 sometimes button 2 will register as well ?

How are you powering your SIGMA and Mistercade ? Pictures please

I am powering the sigma by the psu which is inside the supergun. I am using the Mistercade through the jamma and the supergun psu

 

[raffy92]

It is good that you have a proper GND on your SIGMA.

I believe I have tried Mistercade but on HAS 4.0, IIRC there were no issues.

Just to clarify, your problem is that while pressing button 1 sometimes button 2 will register as well ?

How are you powering your SIGMA and Mistercade ? Pictures please

In the menu or in game I have sometimes to press the button 1, 3 times to have a response

 

[rtw]

Can you snap a picture of the power-plug you use for the SIGMA and a picture of the power supply inside the SIGMA itself ?

 

[raffy92]

 

[rtw]

Thank you, so this means that you do not have any earth/ground in your system. Is there a label on the power supply that you can share a picture of ?

 

[raffy92]

Thank you, so this means that you do not have any earth/ground in your system. Is there a label on the power supply that you can share a picture of ?

ok I will take a picture this evening

 

[raffy92]

I specify that I have a similar issue using a HAS v5.0 bearing a ground

 

[astro_zombie138]

Does anybody tried to run the Mistercade on HAS v5.0 ?

Yes, many times. V1 and V2, no issues for me like this.