Name that connector: the thread
- Thread starter rewrite
- Start date
Well done !
ImportantBet
Grand Master
Looking for a datasheet for this Burndy 160 pin edge connector found on an Aleck64 mobo
I couldn't find any other markings. Looking to use specs (specifically pitch info, etc.) from the datasheet to make a new N64 cart adapter. The pins are too tiny to use a caliper for.
I couldn't find any other markings. Looking to use specs (specifically pitch info, etc.) from the datasheet to make a new N64 cart adapter. The pins are too tiny to use a caliper for.
Attachments
Last edited:
NFGx
Grand Master
You should be able to get a fairly accurate spacing by counting, say, 20 or 30 pins, and measuring that distance. Divide by the total length to get the distance between pins. The more you count before measuring, the more accurate it'll be.
That looks a lot like a PCI* connector. I found several that look like it in photos, but I haven't found specifics yet. Maybe that'll help kick start your hunt.
I'm confused by the markings on the PCB though. I count 160 pins, which it references, but why does it say 82 on the other end? If you count the spacing, it'd be 82 per side - 164 total. So that 82 should be on the other side. Did they count the gap as one pin (which makes 82 accurate) or was it uncounted (which makes 160 accurate)???
This Samtec unit seems pretty close: https://www.samtec.com/products/htec8
You can configure it to be 80 per side and it splits by 32/48 as the Aleck one does. The diagram seems to indicate a larger spacing for the key, so you'd want to check your measurements.
That looks a lot like a PCI* connector. I found several that look like it in photos, but I haven't found specifics yet. Maybe that'll help kick start your hunt.
I'm confused by the markings on the PCB though. I count 160 pins, which it references, but why does it say 82 on the other end? If you count the spacing, it'd be 82 per side - 164 total. So that 82 should be on the other side. Did they count the gap as one pin (which makes 82 accurate) or was it uncounted (which makes 160 accurate)???
This Samtec unit seems pretty close: https://www.samtec.com/products/htec8
Last edited:
Anyone know what connector model is used on Hyper NeoGeo64 Carts?
It's 300 pins and appears to have the Hirose (HRS) logo. Likely discontinued but I'd like to know what model it is to see if I can find some.
It's 300 pins and appears to have the Hirose (HRS) logo. Likely discontinued but I'd like to know what model it is to see if I can find some.
Attachments
SHF-001T-0.8BS was available on Mouser so I made my first purchase from there instead. I found and ordered a few of this part as well- "SHF-001GI-0.8BS". I'm not sure if it is the same contact provided in a different format or what. I'm happy to report back if anyone is interested. I don't recall seeing this part last time I ordered and since JST seems to always have backorders, I figured it couldn't hurt to buy a few and see.
matthijs
Beginner
Anyone know what this connector on a gundam stick is? I was just talking to @Sp33dFr34k about it, we initially thought JST VL but there doesn’t seem to exist a 3x3 version of that connector. Pitch seems to be ~6.2mm.
Attachments
I have a tray full of those, I had to buy a whole pack to get one to repair an Aleck64. I don't remember where I got them but I'll check the parts and tray (looked original vendor supply) for information.
CELP2X80SC-3Z48
stock number (unsure of vendor) 807020
Last edited:
Ziggy Cheetos Dust
Champion
Any idea what this JST is? It’s from the Konami Windy II IO.
NFGx
Grand Master
Those are AMP Universal Power, same as used on Sega cabs.
https://gamesx.com/wiki/doku.php?id=arcade:sega_city_cabinet_pinouts#control_input
https://gamesx.com/wiki/doku.php?id=arcade:sega_city_cabinet_pinouts#control_input
Last edited:
Ziggy Cheetos Dust
Champion
Thank you. No wonder I couldn’t find them. I thought they had J S T written on them, but am away from home and might’ve been thinking of the JST-VLs on the power supply.
NFGx
Grand Master
I found this schematic which has all the connectors and their series/part numbers for the Windy:
1credit
Professional
This is a bit off topic but can someone confirm if I can power this sega io
With + 5v & ground only going in on the CN6 pls ?
My Naomi sun psu loom
Only has jst H 5 pin and Jst H4pin
But The jamma to jvs sega io has a Jst H 6 pin header . Cn6 Thnx
On a previouse thread I found this
pinout from 838-13683-91
But my I/o is a 838-13583-02
Is this pinout correct for my jamma to jvs/jvs to jamma
If you like. ( pin 1 is +5 ? )
And if only +5v is required ? Thanx all …
( cheers for vortex @ rewrite )
Notice in pic below thet the 5v & 12v pins on this
Gd rom pin out is reversed compared to the above cn6 pinout.
But as I don’t have a 6 pin Jst H female connector on my loom.
I want to take a single 5v and single ground wire to cn6 from my i/o from sun psu loom ideally.
Which is what I think I can do,
But looking for confirmation on this ?
As opposed to using the jamma edge 5v 12v which is an option.
But as I have these jst H loom might as well use em !
Assuming gd drive needs 12v for
Cd drive motor. And I/0 only require +5v
Só basically in a nut shell
I have 5v on pin 1 ground on pin 6
Is this going to work?
Pin 1 = +5v
Pin 6 = GND
With + 5v & ground only going in on the CN6 pls ?
My Naomi sun psu loom
Only has jst H 5 pin and Jst H4pin
But The jamma to jvs sega io has a Jst H 6 pin header . Cn6 Thnx
On a previouse thread I found this
pinout from 838-13683-91
But my I/o is a 838-13583-02
Is this pinout correct for my jamma to jvs/jvs to jamma
If you like. ( pin 1 is +5 ? )
And if only +5v is required ? Thanx all …
( cheers for vortex @ rewrite )
Notice in pic below thet the 5v & 12v pins on this
Gd rom pin out is reversed compared to the above cn6 pinout.
But as I don’t have a 6 pin Jst H female connector on my loom.
I want to take a single 5v and single ground wire to cn6 from my i/o from sun psu loom ideally.
Which is what I think I can do,
But looking for confirmation on this ?
As opposed to using the jamma edge 5v 12v which is an option.
But as I have these jst H loom might as well use em !
Assuming gd drive needs 12v for
Cd drive motor. And I/0 only require +5v
Só basically in a nut shell
I have 5v on pin 1 ground on pin 6
Is this going to work?
Pin 1 = +5v
Pin 6 = GND
Last edited:
Ziggy Cheetos Dust
Champion
Thanks mate. I’m a dummy. I’ve been looking at that a lot recently and didn’t twig to look thereI found this schematic which has all the connectors and their series/part numbers for the Windy:
nipple
Enthusiast
Hey guys,
Just had my ms9-29 recapped on reinstall this plug crumbled.
I was able to plug it all in and get a picture still but would like to replace the housing.
It is on the yoke wires.
It has amp but I can’t work out what model it is.
EDIT its aTJC1 from aliexpress or china
Cheers
Just had my ms9-29 recapped on reinstall this plug crumbled.
I was able to plug it all in and get a picture still but would like to replace the housing.
It is on the yoke wires.
It has amp but I can’t work out what model it is.
EDIT its aTJC1 from aliexpress or china
Cheers
Attachments
Last edited:
@nem will know.
Japanese like to use Japanese manufacturers for chips, connectors, etc.
I always have a look at this page first: http://www.jst.co.uk/products.php?cat=1
Japanese like to use Japanese manufacturers for chips, connectors, etc.
I always have a look at this page first: http://www.jst.co.uk/products.php?cat=1