New CPS2 Multigame Firmware with Key Writing!!!!!!

[fredjss]

Hello guys,

My final version of my CPS2 Multigame. Simple but I liked!!

I keep the original green color - simple car paint (but the pcb is South America version)

I asked a friend to put the LCD connector an horizontal position

I had a problem with my soldering iron, and did't time to buy another shell :/)

Sticker from CPS2 Multigame bought at SaveYourGames

Playing "The Punisher"

I'm satisfied with my CPS2 Multigame!

Have fun today!!

 

[Duo_r]

Ok I got an original CPS2 Darksoft. Do I need to follow this exactly:

http://www.mediafire.com/view/bhh42dan8tbtr98/CPS2_Firmware_Update.pdf

Using this file:

http://www.mediafire.com/download/ddvkyn8eisnen52/PFG_____0002.rar


And then I can just use a SD card and flash the latest firmware? I’ve read a ton of posts but confused what to do for original release boards.

 

[Mitsurugi-w]

Are you sure it has not been updated already?

 

[Duo_r]

Yes positive. I tried shooting you an email but not sure I got the right address. I got my board in 2015.

 

[Darksoft]

Try the guide. If you can't do it, mitsurugi could do it for you for a small fee.

 

[Duo_r]

So my Bootloader was updated and so was the firmware. I can tell because the LCD says “programming key” when powering up and the Flash.img disappeared after booting.

However I’m getting a solid light blue screen now. No sound nothing. Not sure what to do. I used a flathead to short EXC5, just the outer legs to the inner leg. Didn’t do anything. I formatted the SD and loaded back in my “old” rollup kit which should work. I haven’t installed the Key wirings yet. Anyone have Any ideas??!

 

[Duo_r]

I reseated the board and did the 30 second trick with exc5. It works now! I guess it’s time to install the key wires now! Thanks to Mitsu for all the help! Darksoft products are A+++

 

[SabreAZ]

I bought my kit like 2 months ago, I presume I should be safe with installing the wiring? I would doubt the online vendors would have any old backstock old boards

 

[CPZ - SAVEYOURGAMES]

All the multi sold in the last year have the new firmware, don't worry

 

[mastercello]

Are you sure it has not been updated already?

I update mine to a new firmware in 2015 or 2016 i presume - but unsure if it is already able to do it now via sd card - how can i check this the easiest way?

 

[Darksoft]

just copy the latest firmware in the microSD. It's a file called flash.img. Power on the CPS2 Multi and wait for 15 seconds. Check the microSD in the PC. If the file is deleted, then the update went well.

 

[mastercello]

Gracias Señor!

If not i can update via STM32 using the same flash.img file - right?

 

[Darksoft]

that's right!

 

[nonosto]

So I need one info for one buddy. He has one ssf2X jap, what's must I do to run the multi cps2?

 

[jassin000]

He has one ssf2X jap, what's must I do to run the multi cps2?

Same as any other CPS2 B-board (so I really don't know why you are asking) strip it down/make it bare (aka pull all the MASKROMs).
Cut the battery off (assuming its still on battery) set the jumpers correctly, solder the reset/key wires and install the multi PCB.

If you don't already have a G-PAL, get one and install it (I think SSF2X is G-PAL stock but I don't remember).

 

[xodaraP]

SSF2X is a D PAL

It will need the daughter board and other ROMs removed, a G PAL and jumper wire

Edited as per Mitsurugi-w

 

[Mitsurugi-w]

You don't need to mess with the jumpers. It should work as long as they were set correctly for the game that was installed.

 

[xodaraP]

I retract and have edited my previous statement

When did that change?

 

[jassin000]

When did that change?

Depends on the game used, Marvel vs Capcom didn't need any jumper setting/resetting for example.
Its for this hastlefree reason I recommend using this game.

Sure others work just fine, but lets review all the features that make MvC the best doner board.

• G-PAL stock
• Jumpers pre-configured for the multi
• Rev 7 motherboard (assuming its NOT a factory rework)

 

[owlnonymous]

I need to convert my CPS2 unencrypted multi, and setup a friend's new multi this weekend. Is there a best/good guide for doing either? Sorry, I looked around and I'm only seeing bits and pieces of information.