snakeGrave
Professional
Never made it onto the list but im in for one of available
Interest Check: Repo Restrictor disc for Gundam Stick Monkey Ball joysticks…
- Thread starter nam9
- Start date
plasticfactory
Champion
No worries, I basically doubled the initial interest check quantity so that there is inventory for anyone late to the party.
Looks great! Can’t waitBehold:
I'm going to run these through an ultrasonic, dryer, then packaging. I'll being taking orders/shipping before the end of this week.
plasticfactory
Champion
After way too long:
matthijs
Beginner
looks great! I sent you a DM
AU and NZ peeps, we now have these on CandyCabClub: https://www.candycabclub.com/product/monkeyball_restrictor
Will be installing one onto my stick tomorrow for some testing. They look great!
Will be installing one onto my stick tomorrow for some testing. They look great!
A little off-topic but what's the best way to get a gundam compatible banana to complete the panels?
Using the 3D print from @nnap https://www.thingiverse.com/thing:4590353
thank you nnap for making this available!
Looking at PCBway to print this but so many 3D printing options there:
Yellow PETG?
Using the 3D print from @nnap https://www.thingiverse.com/thing:4590353
thank you nnap for making this available!
Looking at PCBway to print this but so many 3D printing options there:
Yellow PETG?
nnap
Grand Master
I can print one for you if you want.
plasticfactory
Champion
Printing is the best option currently, but since it was brought up, I will be injection molding reproductions. They will be blue light scanned and as 1:1 as possible, with variable shaft options. It will be Q4 or Q1 2026 (another molding project supercedes this)
In the mean time, nnap is who I would talk to
In the mean time, nnap is who I would talk to
Hey @nem could you advise the areas that need grease applied on the stick? I'm going to clean everything up and wanted to make sure I hit all the needed parts.I received one of the production samples made by @plasticfactory.
It definitely looks and feels the part. The black disc in front is a chewed up, original one.
Installed in, fitment is perfect. It's ready to be abused. I run an arcade and Monkey Ball is fairly popular here, so we'll see how it holds up! My guess is it's going to take months to see wear on it though.
Around and under the disc, around the rotating plastic cylinders. Basically everywhere you have plastic moving against other plastic or metal.
I actually regreased the Monkey Ball stick not long ago. The repro disc was completely unscathed.
I actually regreased the Monkey Ball stick not long ago. The repro disc was completely unscathed.
Cleaned the stick and applied grease as per @nem's suggestion.
I'm wired directly from the Blast City cabs I/O into the SEGA JVS I/O. Stick is connected directly to the Op Amp then routed through the Blast. The 2K resistors have been installed into the cable connected to the stick (cable far left in photo below), as made by @Lemony Vengeance. A very elaborate set of wiring required to get the neatest result possible!
Everything feels fine, much better with a restricted stick. I didn't do playing before installing, so have no baseline to compare to, however I'm getting more restricted readings after calibration, here's where I'm sitting.
NOW H: 86H / 134
NOW V: 8FH / 143
LEFT: 5BH / 91
RIGHT: ADH / 173
PUSH: 60H / 96
PULL: B8H / 184
I couldn't find anywhere which listed solid readings for this setup anywhere and was wondering if this matches up with anyone else with the same setup, or how it compares to the original setup?
I'm wired directly from the Blast City cabs I/O into the SEGA JVS I/O. Stick is connected directly to the Op Amp then routed through the Blast. The 2K resistors have been installed into the cable connected to the stick (cable far left in photo below), as made by @Lemony Vengeance. A very elaborate set of wiring required to get the neatest result possible!
Everything feels fine, much better with a restricted stick. I didn't do playing before installing, so have no baseline to compare to, however I'm getting more restricted readings after calibration, here's where I'm sitting.
NOW H: 86H / 134
NOW V: 8FH / 143
LEFT: 5BH / 91
RIGHT: ADH / 173
PUSH: 60H / 96
PULL: B8H / 184
I couldn't find anywhere which listed solid readings for this setup anywhere and was wondering if this matches up with anyone else with the same setup, or how it compares to the original setup?
FrAshi
Professional
Finally got mine installed (with some fresh grease), thanks @plasticfactory and everyone who worked on this project!
Are you using the op amp? Can you post your calibration readings?!
FrAshi
Professional
Attachments
Cheers. Your values converted from HEX to DEC are:
NOW H: 85/133
NOW V: 95/149
LEFT: 60/96
RIGHT: B1/177
PUSH: 60/96
PULL: C0/192
------
Your travel between axis are:
Left & Right: 81
Push & Pull: 96
My travel is:
Left & Right: 82
Push & Pull: 88
Assuming you are too using the Op Amp and Resistors in-line.
Seems like I'm missing a bit of range on the Push & Pull, compared to you, but I'm going to guess that's about right given some allowance between sticks age, etc.
Would be good to get readings from others, or someone with the original game....
NOW H: 85/133
NOW V: 95/149
LEFT: 60/96
RIGHT: B1/177
PUSH: 60/96
PULL: C0/192
------
Your travel between axis are:
Left & Right: 81
Push & Pull: 96
My travel is:
Left & Right: 82
Push & Pull: 88
Assuming you are too using the Op Amp and Resistors in-line.
Seems like I'm missing a bit of range on the Push & Pull, compared to you, but I'm going to guess that's about right given some allowance between sticks age, etc.
Would be good to get readings from others, or someone with the original game....
Last edited:
FrAshi
Professional
I pushed it hard as well, to get max readings
I actually finally got around to building my panel yesterday (after having all these parts collecting dust for ages).
with an unmodified amp board and the restrictor I'm blowing out the ranges... calibration goes from 00 to FF before I even hit the limit.
I'm guessing the original MonkeyBall pots have a larger range that the amp helps tune? would be nice to know the readings on an original setup.
it occurs to me adding 2 small pots on the amp board between the CN2 5V and GND pins and the rest of the circuit would give you a calibratable setup.
with an unmodified amp board and the restrictor I'm blowing out the ranges... calibration goes from 00 to FF before I even hit the limit.
I'm guessing the original MonkeyBall pots have a larger range that the amp helps tune? would be nice to know the readings on an original setup.
it occurs to me adding 2 small pots on the amp board between the CN2 5V and GND pins and the rest of the circuit would give you a calibratable setup.
Last edited:
@twistedsymphony
Interesting explanation from John Bennet over on UKVAC
If you want to use the amp board then you do need to go the extra distance and replace the lots, but otherwise the MB calibration will handle the pots as is.
Interesting explanation from John Bennet over on UKVAC
If you want to use the amp board then you do need to go the extra distance and replace the lots, but otherwise the MB calibration will handle the pots as is.