What's new
By:

Retro Hardware Capacitors LISTS

I did Turtles In Time last week. Here is the capmap

IMG_5262.jpeg


IMG_5263.jpeg
 
Finished recapping the 400-5198-01 and 400-5198-01X PSUs in my New Astro Citys. They are identical:

Code: 
Capacitor      Diameter      Qty      Location
0.47uF 50V     5.00mm        1        C10
3.3uF 50V      5.00mm        1        C23
47uF 25V       5.00mm        1        C22   
330uF 200V     22.00mm       1        C5       
470uF 16V      10.00mm       1        C20
1000uF 35V     12.50mm       2        C18, C19
4700uF 10V     16.00mm       4        C11, C12, C13, C14
 
More Astro City PSU recap work. The models are:

400-5261
Code: 
Capacitor      Diameter      Qty      Location
0.47uF 50V     5.00mm        1        C11
3.3uf 50V      5.00mm        1        C26
100uf 25V      6.30mm        1        C25
470uf 10V      8.00mm        1        C28
470uF 16V      10.00mm       1        C23
470uf 200V     30.00mm       1        C5
1000uF 35V     12.50mm       2        C21, C22
6800uf 10V     16.00mm       6        C12, C13, C14, C15, C16, C17

400-5198-01Y
Code: 
Capacitor      Diameter      Qty      Location
0.47uF 50V     5.00mm        1        C27
10uf 50V       5.00mm        2        C8, C14
47uF 25V       5.00mm        1        C7
100uf 25V      6.30mm        1        C13
330uF 200V     22.00mm       1        C5
2200uf 16V     12.50mm       1        C17
6800uf 10V     16.00mm       2        C22, C23
 
Thanks for maintaining these lists, I've used them to compile kits for five of my boards so far. I've just had my next bundle delivered:

IMG_2871.jpg


So if Mouser shows all of the usual Panasonic caps as out of stock, it's probably because I bought them all.

Sorry, not sorry :D
 
The following 3mm diameter capacitor is used to recap Namco NA-1 boards but it's not in production anymore. It could be replaced by a 4mm capacitor but I'm wondering if it will fit and could be soldered on the existing pads. Any idea?

2.2uF35vSMDx7647-UWX1V2R2MCL2

Thanks,
\o/.k.
 
kebrank said:
The following 3mm diameter capacitor is used to recap Namco NA-1 boards but it's not in production anymore. It could be replaced by a 4mm capacitor but I'm wondering if it will fit and could be soldered on the existing pads. Any idea?

2.2uF35vSMDx7647-UWX1V2R2MCL2

Thanks,
\o/.k.
Click to expand...
Should fit to pads, 1mm ain't nothing.
 
Omron S8XA-0731 power supply from a Konami Windy

1x 470uf 200v
1x 680uf 35v
1x 47uf 63v
2x 200uf 35v
3x 3900uf 10v
2x 1200uf 10v
1x 220uf 10v
1x 4.7uf 50v

(Edited to add the little cap I missed at the upper right, the 4.7uf)

FAvPAL-UUAM4cAu.jpeg
 
Last edited:
I've just compiled the cap list for Donpachi PCB. I took it from a Korean or Overseas pcb:
  • 3 x 47uf 16V
  • 2 x 100uF 16V
  • 3 x 1000uF 16V
  • 1 x 470uF 16V
  • 2 x 10uF 16V
Positions:
  • C2: 47uf 16V (for reset circuit)
  • C17: 47uF 16V
  • C18: 47uF 16V
  • C5: 100uF 16V
  • C8: 100uF 16V
  • C7: 1000uF 16V
  • C10: 1000uF 16V
  • C12: 1000uF 16V
  • C13: 470uF 16V
  • C22: 10uF 16V
  • C28: 10uF 16V

Could someone with Japan version PCB confirm these values? (Sometimes cheap korean pcbs have some little changes in values that could potencially cause little issues in audio signal)
 
Hy.

I have a question concerning the Sega st-v list. It says there 10uf 50v for all 10uf caps. But my two boards here have all 10uf 16v. I know you can take higher value here. But it’s about the correct original caps in the list. Right?
 
hardyhell said:
Hy.

I have a question concerning the Sega st-v list. It says there 10uf 50v for all 10uf caps. But my two boards here have all 10uf 16v. I know you can take higher value here. But it’s about the correct original caps in the list. Right?
Click to expand...
I don't have a Sega STV board on hand to compare against, but it's possible that Sega switched to the larger-voltage caps in a later production run. Updating the list to say 16V or 50V may be a good idea.
 
There's a small error on the Sega System 24 list. The individual capacitors are correct but the totals are wrong.

The totals say 3x 2.2µF and 8x 10µF, but it should be corrected to 5x 2.2µF and 6x 10µF.

I've just realised I'm missing a couple of 2.2µF caps :cursing:
 
I found a couple of missing boards to add to the list:

Truxton/Tatsujin

CapacitorRatingTypeLead spacing or dimensions
C116V 470µFRadial5mm
C216V 10µFAxial12mm x 5mm
C316V 10µFAxial12mm x 5mm
C516V 10µFAxial12mm x 5mm
C616V 220µFAxial16mm x 8mm
C716V 22µFAxial12mm x 5mm
C816V 10µFAxial12mm x 5mm
C1616V 470µFRadial5mm

IMG_3076.jpeg


Strikers 1945 (Psikyo SH404)

CapacitorRatingTypeLead spacing or dimensions
C216V 10µFRadial2mm
C716V 100µFRadial2.5mm
C816V 100µFRadial2.5mm
C916V 100µFRadial2.5mm
C1035V 4.7µFRadial2mm
C1535V 4.7µFRadial2mm
C1635V 4.7µFRadial2mm
C1716V 10µFRadial2mm
C1825V 2200µFRadial7.5mm
C1916V 47µFRadial2mm
C2116V 100µFRadial2.5mm
C2216V 100µFRadial2.5mm
C2316V 100µFRadial2.5mm

IMG_3077.jpeg


Sol Divide (Psikyo PS3-V1)

CapacitorRatingTypeLead spacing or dimensions
C125V 100µFRadial2.5mm
C225V 4.7µFRadial2.5mm
C425V 4.7µFRadial2.5mm
C716V 10µFRadial2.5mm
C1025V 4.7µFRadial2.5mm
C1325V 2200µFRadial7.5mm
C1525V 100µFRadial2.5mm
C1625V 4.7µFRadial2.5mm
C1825V 100µFRadial2.5mm
C1916V 47µFRadial2.5mm
C2025V 100µFRadial2.5mm
C2225V 100µFRadial2.5mm
C2325V 100µFRadial2.5mm
C2425V 100µFRadial2.5mm

IMG_3078.jpg
 
Another PSU:

NVS-4000-01

Code: 
NVS-4000-01 - Soundboard - SJ25-0303-01 01-0351:

Capacitor    Diameter        Qty        Location
1uf 50V      5.30mm          2          C21, C22
2.2uf 50V    5.30mm          4          C16, C18, C19, C20
10uf 50V     5.30mm          4          C13, C14, C15, C17
33uf 50V     6.30mm          2          C23, C25
100uf 50V    8.00mm          2          C3, C4
4700uf 35V   18.00mm         2          C1, C2

NVS-4000-01 - Powerboard - 01-0359A (on sticker):

Capacitor    Diameter        Qty        Location
1uf 50V      5.30mm          4          C11, C12, C13, C26
2.2uf 50V    5.30mm          2          C18, C28
3.3uf 50V    5.30mm          1          C36
4.7uf 50V    5.30mm          1          C49
22uf 50V     5.30mm          1          C21
33uf 25V     5.30mm          1          C20
100uf 50V    7.50mm          1          C30
330uf 16V    8.00mm          1          C37
470uf 16V    10.00mm         1          C43
680uf 200v   22.00mm         2          C6, C7
1000uf 16V   10.00mm         2          C34, C35
2200uf 10V   12.50mm         3          C42, C47, C48
3300uf 10V   12.50mm         1          C41
3300uf 16V   16.00mm         1          C44
 
Namco NB-2 (Outfoxies, Mach Breakers)

Main PCB - All caps are SMD

C1: 100uF 16v
C12: 470uF 16v
C13: 100uF 6v
C16: 100uF 6v
C17: 100uF 16v
C18: 100uF 6v
C19: 100uF 6v
C22: 2.2uF 50v
C25: 47uF 16v
C26: 47uF 16v
C27: 47uF 16v
C28: 2.2uF 50v
C34: 100uF 16v
C37: 1uF 50v

ROM PCB - cap is axial lead
C1: 470uF 16v

CAP TOTAL Quantities Needed
1 x 1uF 50V SMD
2 x 2.2uF 50v SMD
3 x 47uF 16v SMD
4 x 100uF 6v SMD
3 x 100uF 16v SMD
1 x 470uF 16v SMD
1 x 470uF 16v axial lead

IMG_2881.jpgIMG_2882.jpgIMG_2883.jpg
 
Last edited:
You must log in or register to reply here.
Back
Top